AES power supply kit mods?

Register

Guest Join Us

Hello Guest,

Please feel free to join us!
There are many more parts of the Phorum that only members can see.

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

AES power supply kit mods?

ccomer1955
Senior Member

Posts: 264
Threads: 51
Joined: Aug 2014
City: San Antonio, TX

#10

08-01-2015, 03:00 PM

I measured the D3 output, and it is close to perfect. 12.47 vdc. Will the .47 vdc hurt my fan?

Thanks for the expert help, I now have a wiring harness for inside the box to the voltages I need for the two radios I use with it, a toggle switch and fuse on the mains, a red LED power on light, and a 12vdc fan for the heat sink. Later, I will cut and drill some holes and mount the power supply in the box.

Charlie in San Antonio

Find

« Next Oldest | Next Newest »

Messages In This Thread

AES power supply kit mods? - by ccomer1955 - 07-23-2015, 12:49 PM

RE: AES power supply kit mods? - by morzh - 07-23-2015, 02:50 PM

RE: AES power supply kit mods? - by ccomer1955 - 07-23-2015, 06:05 PM

RE: AES power supply kit mods? - by ccomer1955 - 07-30-2015, 10:17 PM

RE: AES power supply kit mods? - by morzh - 07-31-2015, 10:41 AM

RE: AES power supply kit mods? - by ccomer1955 - 07-31-2015, 01:40 PM

RE: AES power supply kit mods? - by morzh - 07-31-2015, 02:30 PM

RE: AES power supply kit mods? - by ccomer1955 - 07-31-2015, 10:02 PM

RE: AES power supply kit mods? - by morzh - 07-31-2015, 10:09 PM

RE: AES power supply kit mods? - by ccomer1955 - 08-01-2015, 03:00 PM

RE: AES power supply kit mods? - by ccomer1955 - 08-02-2015, 02:06 PM

RE: AES power supply kit mods? - by morzh - 08-02-2015, 04:35 PM

RE: AES power supply kit mods? - by Arran - 08-04-2015, 05:56 AM

RE: AES power supply kit mods? - by Raleigh - 09-02-2015, 09:06 PM

RE: AES power supply kit mods? - by ccomer1955 - 09-02-2015, 10:22 PM

RE: AES power supply kit mods? - by Raleigh - 09-03-2015, 06:14 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A5...MrFixr55 — 06:48 AM

Who's Online

There are currently 4323 online users. [Complete List]
» 4 Member(s) | 4319 Guest(s)