RAS-1

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

RAS-1

Radioroslyn
Phorum Expert

Posts: 7,286
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

08-18-2015, 10:42 PM

Got the magnet off finally. Twisted the tips on two large screw drivers to do it. Boy those bolts where tight. Been on there since 1-40. Inside it was dirty and gritty. Vacuum it out and then used a card to clean out the gap between the pole and magnet. Set the magnet over the voice coil and loosely bolted it. Tried to get it to move freely but no dice so will try the brute force method. That would be adding a few watts of audio to the VC and moving the magnet for best sound. Will get to it tomorrow.

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

RAS-1 - by Radioroslyn - 08-13-2015, 06:59 PM

RE: RAS-1 - by morzh - 08-14-2015, 10:05 AM

RE: RAS-1 - by Radioroslyn - 08-18-2015, 10:42 PM

RE: RAS-1 - by Radioroslyn - 08-24-2015, 07:19 PM

RE: RAS-1 - by Radioroslyn - 08-24-2015, 10:00 PM

RE: RAS-1 - by sam - 08-24-2015, 10:31 PM

RE: RAS-1 - by Radioroslyn - 08-25-2015, 07:12 AM

RE: RAS-1 - by Radioroslyn - 10-27-2015, 07:57 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

Who's Online
There are currently no members online.

Login
Username:
Password:	Lost Password?
	Remember me