Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-180 and PILOTUNER
#5

Unsolder the wire attached to the ungrounded side of the volume control, and attach center wire of PILOTUNER connector cable to this spot. The outside shielded wire of the radio receiver. The disconnected lead from the volume control should be soldered to the center wire of a second connector cable, and through it connected to terminal #5 of the PILOTUNER. The shielded wire of this second cable should also be soldered to chassis. The radio receiver will then operate normally on standard broadcast (AM), whenever the ON-OFF switch of the FM PILOTUNER is in the OFF position.


Can someone translate this ...i can follow it up to "Unsolder the wire attached to the ungrounded side of the volume control, and attach center wire of PILOTUNER connector cable to this spot.

But beyond that im lost .


Messages In This Thread
40-180 and PILOTUNER - by Howard Stricklin - 02-24-2009, 05:32 PM
Re: 40-180 and PILOTUNER - by yesterdaysradios - 02-24-2009, 09:53 PM
Re: 40-180 and PILOTUNER - by FStephenMasek - 02-24-2009, 10:51 PM
Re: 40-180 and PILOTUNER - by Howard Stricklin - 02-24-2009, 11:15 PM
Re: 40-180 and PILOTUNER - by Howard Stricklin - 02-26-2009, 11:45 AM
Re: 40-180 and PILOTUNER - by FStephenMasek - 02-27-2009, 01:06 PM
Re: 40-180 and PILOTUNER - by Howard Stricklin - 02-27-2009, 07:02 PM
Re: 40-180 and PILOTUNER - by Howard Stricklin - 02-27-2009, 07:11 PM
Re: 40-180 and PILOTUNER - by Doug Houston - 02-28-2009, 01:37 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Gilfillan Brothers Car Radio?
Hi everyone,  Special thanks to Joe Rossi for tracking down this obscure radio and thanks to others who took up the hun...Antipodal — 08:15 PM
trying to identify this wire type
Here's one source for your wire of many. Take care and BE HEALTHY! Gary P.S. Can't get the right color you need? I ...GarySP — 06:40 PM
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM

[-]
Who's Online
There are currently 4276 online users. [Complete List]
» 1 Member(s) | 4275 Guest(s)
Avatar

>