Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

EICO 320 Signal Generator
#3

What some folks do is get the calibration good at the low end (for the IF frequencies) and use the BC stations to align ant/osc stages.

Terry


Messages In This Thread
EICO 320 Signal Generator - by Crist Rigotti - 08-25-2015, 10:57 PM
RE: EICO 320 Signal Generator - by codefox1 - 08-26-2015, 06:36 AM
RE: EICO 320 Signal Generator - by Radioroslyn - 08-28-2015, 07:02 PM
RE: EICO 320 Signal Generator - by Crist Rigotti - 08-28-2015, 09:21 PM
RE: EICO 320 Signal Generator - by Mitch - 07-27-2016, 01:11 AM
RE: EICO 320 Signal Generator - by PhilcoMike - 07-27-2016, 03:04 PM
RE: EICO 320 Signal Generator - by Joe Rossi - 07-27-2016, 07:53 PM
RE: EICO 320 Signal Generator - by TV MAN - 07-28-2016, 07:19 AM
RE: EICO 320 Signal Generator - by Crist Rigotti - 07-28-2016, 09:44 AM
RE: EICO 320 Signal Generator - by gregb - 07-28-2016, 05:03 PM
RE: EICO 320 Signal Generator - by PhilcoMike - 07-29-2016, 03:08 PM
RE: EICO 320 Signal Generator - by Crist Rigotti - 07-31-2016, 10:08 PM
RE: EICO 320 Signal Generator - by Mitch - 07-30-2016, 12:38 AM
RE: EICO 320 Signal Generator - by PhilcoMike - 08-01-2016, 02:08 PM
RE: EICO 320 Signal Generator - by Crist Rigotti - 08-02-2016, 10:09 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 3679 online users. [Complete List]
» 2 Member(s) | 3677 Guest(s)
AvatarAvatar

>