Help with a Philco 89B

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Help with a Philco 89B

kiwi_steve
A Kiwi, called Steve

Posts: 134
Threads: 11
Joined: Jul 2015
City: Christchurch, New Zealand

#23

08-30-2015, 02:27 AM

replaced the cooked wire, modified and inserted insulator and tested... ran up fine with most voltages within about 5% of the listed values. I'm actually pretty amazed that this was the only problem (so far). Its picking up several local stations without any aerial, and a very short (12") piece of wire on the aerial terminal about doubled the volume... most of the trimmers were already near enough to peaked so alignment should be straight forward (well, here's hoping) - I did measure all the capacitance's of the trimmers before pulling it apart, and reset them on reassembly.

I suppose I should do a power up video... thats for another day as I'm heading out... but all good, I'm smiling now Icon_biggrin

There are no personal problems that can't be overcome with the liberal application of high explosives

Find

« Next Oldest | Next Newest »

Messages In This Thread

Help with a Philco 89B - by kiwi_steve - 07-26-2015, 03:07 PM

RE: Help with a Philco 89B - by kiwi_steve - 07-26-2015, 03:34 PM

RE: Help with a Philco 89B - by Steve Davis - 07-26-2015, 05:11 PM

RE: Help with a Philco 89B - by morzh - 07-26-2015, 09:54 PM

RE: Help with a Philco 89B - by klondike98 - 07-26-2015, 10:02 PM

RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 07:44 AM

RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 07:59 AM

RE: Help with a Philco 89B - by morzh - 07-27-2015, 10:44 AM

RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 02:33 PM

RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 02:40 PM

RE: Help with a Philco 89B - by morzh - 07-27-2015, 03:14 PM

RE: Help with a Philco 89B - by kiwi_steve - 07-27-2015, 05:42 PM

RE: Help with a Philco 89B - by kiwi_steve - 07-28-2015, 02:51 AM

RE: Help with a Philco 89B - by sam - 07-28-2015, 03:00 AM

RE: Help with a Philco 89B - by kiwi_steve - 07-28-2015, 05:18 AM

RE: Help with a Philco 89B - by morzh - 07-28-2015, 09:49 AM

RE: Help with a Philco 89B - by kiwi_steve - 07-29-2015, 08:06 AM

RE: Help with a Philco 89B - by GarySP - 07-29-2015, 08:35 AM

RE: Help with a Philco 89B - by kiwi_steve - 07-29-2015, 05:10 PM

RE: Help with a Philco 89B - by kiwi_steve - 08-01-2015, 07:48 PM

RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 12:16 AM

RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 01:11 AM

RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 02:27 AM

RE: Help with a Philco 89B - by kiwi_steve - 08-30-2015, 08:54 PM

RE: Help with a Philco 89B - by kiwi_steve - 09-02-2015, 06:39 PM

RE: Help with a Philco 89B - by Arran - 09-03-2015, 01:03 AM

RE: Help with a Philco 89B - by kiwi_steve - 09-03-2015, 04:28 PM

RE: Help with a Philco 89B - by kiwi_steve - 09-22-2015, 05:18 PM

RE: Help with a Philco 89B - by kiwi_steve - 10-20-2015, 12:19 AM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM
Philco 38-7 Speaker
I know that when I first started working on this radio, I did not even have a speaker. Once I finally found one it was n...tludka — 11:00 PM
Philco 60 Squealing
I seem to remember eliminating a squeal by changing the IF frequency by a few KHz. Not that you should put too much tru...fenbach — 08:48 PM
Philco 42-390, code 121 speaker
These speakers pop up on eBay regularly, even if at bloated prices. Honestly, have not seen many parts on swapmeets.morzh — 08:38 PM
Philco 38-7 Speaker
The put-put is not like the speaker problem.morzh — 08:29 PM
Mission Bell Model 19A Car Radio
Hello everyone, As mentioned in my last post I was going to see if the vibrator / rectifier section could be persuaded...Antipodal — 08:21 PM
Philco 60 Squealing
Wondering if I did it backwards. If a coil was wound backwards, the oscillator would not work at all. Old school...Chas — 07:23 PM
Philco 38-7 Speaker
4-ohm speaker. Black, Green leads.tludka — 07:00 PM
Philco 42-390, code 121 speaker
#87 on the schematic. This radio had a 8" Zenith speaker attached to it when I got it. I do don't know the hist...Stevelog — 06:39 PM

Who's Online

There are currently 2225 online users. [Complete List]
» 1 Member(s) | 2224 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me