1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Model 70 Question
bm071
Member
***
Posts: 53
Threads: 12
Joined: Jun 2011
City: Lexington, N.C. 27292
#1

08-30-2015, 09:28 AM
Hello,

 I jsut sold my Model 70 this past week and another one was given to me yesterday. Guess I'm meant to have one in my collection. The radio plays pretty good except for the low end of the band, could be a weak tube, I cannot test them... My question is about alignment procedure,,,I see there are  three trimmers on the tuning condenser, is there a specific sequence of adjustment? or just trim out?

Bob  


Attached Files Image(s)
               
Find
« Next Oldest | Next Newest »


Messages In This Thread
Model 70 Question - by bm071 - 08-30-2015, 09:28 AM
RE: Model 70 Question - by Steve Davis - 08-30-2015, 10:36 AM
RE: Model 70 Question - by bm071 - 08-30-2015, 11:29 AM
RE: Model 70 Question - by Philco281989 - 09-05-2015, 11:21 AM
RE: Model 70 Question - by morzh - 08-30-2015, 12:08 PM
RE: Model 70 Question - by bm071 - 08-30-2015, 01:58 PM
RE: Model 70 Question - by TV MAN - 09-05-2015, 08:49 AM
RE: Model 70 Question - by Radioroslyn - 09-05-2015, 01:53 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration