Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Gilfillan radio?
#3

That's a west coast radio for sure, but what an odd knob arrangement.  It doesn't look like a hole has been filled where a third knob would be on the right, but I've never seen an odd knob set-up like this before.  You'd think they would have placed the knob directly under the tuning knob.

I'd sure like to see a picture of the front of the chassis and the inside front of that cabinet if you get a chance.  When I get back to my other PC I'll see if I can find a schematic in my Gernsback manuals; they seem to have a lot of the west coast sets that Riders doesn't.

Also, what does that little plate on the front of the cabinet say?

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"


Messages In This Thread
Gilfillan radio? - by Eric - 08-31-2015, 10:57 AM
RE: Gilfillan radio? - by OldRestorer - 08-31-2015, 11:34 AM
RE: Gilfillan radio? - by Eliot Ness - 08-31-2015, 11:39 AM
RE: Gilfillan radio? - by Eric - 08-31-2015, 01:35 PM
RE: Gilfillan radio? - by Mondial - 08-31-2015, 02:15 PM
RE: Gilfillan radio? - by Eric - 08-31-2015, 06:02 PM
RE: Gilfillan radio? - by Paul Philco322 - 08-31-2015, 08:18 PM
RE: Gilfillan radio? - by Mondial - 08-31-2015, 08:29 PM
RE: Gilfillan radio? - by Eliot Ness - 09-01-2015, 12:13 PM
RE: Gilfillan radio? - by Eric - 09-01-2015, 12:20 PM
RE: Gilfillan radio? - by Eliot Ness - 09-01-2015, 02:49 PM
RE: Gilfillan radio? - by Mondial - 09-01-2015, 08:22 PM
RE: Gilfillan radio? - by Eric - 09-02-2015, 09:08 AM
RE: Gilfillan radio? - by Eric - 09-01-2015, 08:34 PM
RE: Gilfillan radio? - by Eliot Ness - 09-02-2015, 11:55 AM
RE: Gilfillan radio? - by Mondial - 09-02-2015, 01:15 PM
RE: Gilfillan radio? - by Eric - 09-02-2015, 07:51 PM
RE: Gilfillan radio? - by Eric - 09-03-2015, 10:58 AM
RE: Gilfillan radio? - by Mondial - 09-03-2015, 12:43 PM
RE: Gilfillan radio? - by Eric - 09-03-2015, 02:08 PM
RE: Gilfillan radio? - by Mondial - 09-03-2015, 03:55 PM
RE: Gilfillan radio? - by Eric - 09-03-2015, 06:28 PM
RE: Gilfillan radio? - by Mondial - 09-03-2015, 08:53 PM
RE: Gilfillan radio? - by Eric - 09-04-2015, 09:47 AM
RE: Gilfillan radio? - by Mondial - 09-04-2015, 03:15 PM
RE: Gilfillan radio? - by Eric - 09-04-2015, 03:56 PM
RE: Gilfillan radio? - by Mondial - 09-04-2015, 06:11 PM
RE: Gilfillan radio? - by Eric - 09-04-2015, 07:31 PM
RE: Gilfillan radio? - by Mondial - 09-04-2015, 08:49 PM
RE: Gilfillan radio? - by Eric - 09-05-2015, 09:20 AM
RE: Gilfillan radio? - by Eric - 09-16-2015, 04:57 PM
RE: Gilfillan radio? - by Arran - 09-17-2015, 12:30 AM
RE: Gilfillan radio? - by Eric - 09-17-2015, 11:06 AM
RE: Gilfillan radio? - by Mondial - 09-17-2015, 03:49 PM
RE: Gilfillan radio? - by Eric - 09-17-2015, 04:17 PM
RE: Gilfillan radio? - by Eric - 09-17-2015, 05:14 PM



Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>