1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
half the tubes check bad
klondike98
Phorum Moderator
******
Posts: 5,084
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#11

09-09-2015, 11:37 PM
Icon_thumbup Icon_thumbup Icon_thumbup
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »


Messages In This Thread
half the tubes check bad - by doc612 - 07-13-2015, 12:01 PM
RE: half the tubes check bad - by Nick3092 - 07-13-2015, 01:04 PM
RE: half the tubes check bad - by doc612 - 07-13-2015, 04:21 PM
RE: half the tubes check bad - by morzh - 07-13-2015, 01:14 PM
RE: half the tubes check bad - by doc612 - 07-13-2015, 04:22 PM
RE: half the tubes check bad - by TA Forbes - 07-13-2015, 01:40 PM
RE: half the tubes check bad - by TA Forbes - 07-13-2015, 01:41 PM
RE: half the tubes check bad - by doc612 - 07-13-2015, 04:25 PM
RE: half the tubes check bad - by TA Forbes - 07-13-2015, 08:36 PM
RE: half the tubes check bad - by doc612 - 09-09-2015, 11:19 PM
RE: half the tubes check bad - by klondike98 - 09-09-2015, 11:37 PM
RE: half the tubes check bad - by tom.seeger - 09-12-2015, 10:03 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Any 6.3 volt pilot light will work. I would use the brightest one I could find in my workroom. Be sure the dial is clean...RodB — 10:45 AM
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM

[-]
Who's Online
There are currently 7830 online users. [Complete List]
» 2 Member(s) | 7828 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration