1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
capacitor crossreference
Howard R Stricklin
Member
***
Posts: 62
Threads: 9
Joined: Dec 2008
City: loogootee indiana
#20

03-04-2009, 09:32 AM
Iv figured out where the wire that came off went thanks to gary rabbitt ...but still get no power when i switch it on ..iv only replaced one capacitor
it is a .1mfd ..this is really getting frustrating as it would at least light the tubes and make my 40-180 hum when it was tuned to it before i replaced the first cap..Im getting close to skyhooking it into the dumpster out back .
Find
« Next Oldest | Next Newest »


Messages In This Thread
capacitor crossreference - by Howard Stricklin - 02-15-2009, 02:22 PM
Re: capacitor crossreference - by Syl - 02-15-2009, 03:27 PM
Re: capacitor crossreference - by AI2V - 02-15-2009, 03:36 PM
Re: capacitor crossreference - by Syl - 02-16-2009, 12:35 AM
Re: capacitor crossreference - by codefox1 - 02-16-2009, 07:02 PM
Re: capacitor crossreference - by Syl - 02-17-2009, 08:07 PM
Re: capacitor crossreference - by gary rabbitt - 02-17-2009, 08:23 PM
Re: capacitor crossreference - by Syl - 02-18-2009, 12:33 AM
Re: capacitor crossreference - by FStephenMasek - 02-18-2009, 01:59 AM
Re: capacitor crossreference - by Jim Berg - 02-18-2009, 03:11 PM
Re: capacitor crossreference - by gary rabbitt - 02-22-2009, 04:42 PM
Re: capacitor crossreference - by Howard Stricklin - 03-04-2009, 09:32 AM
Re: capacitor crossreference - by gary rabbitt - 03-05-2009, 01:43 AM
Re: capacitor crossreference - by Ron Ramirez - 03-09-2009, 09:05 PM
Re: capacitor crossreference - by Ron Ramirez - 09-23-2009, 09:37 AM
Re: capacitor crossreference - by Ron Ramirez - 09-23-2009, 03:39 PM
Re: capacitor crossreference - by Raleigh - 10-03-2009, 01:22 AM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM
IF can wire size and Rubber mounts?
A pair of wire strippers can give you an idea of what the existing gauge of the wire leads are in the IF can, I think it...Arran — 06:07 AM

[-]
Who's Online
There are currently 5166 online users. [Complete List]
» 2 Member(s) | 5164 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration