Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

I'm batting 1000
#3

Well Steve, I just checked it. The oscillator is working, but now WGN is gone and the only thing I can pick up is my SSTRAN set at 1500khz. This would be a step in the right direction except that it is coming in at about 700khz no matter what I do to the osc trimmer on the tuning cap!

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org



Messages In This Thread
I'm batting 1000 - by Eric Adams - 09-21-2015, 11:17 PM
RE: I'm batting 1000 - by Steve Davis - 09-21-2015, 11:28 PM
RE: I'm batting 1000 - by Eric Adams - 09-22-2015, 12:18 AM
RE: I'm batting 1000 - by Steve Davis - 09-22-2015, 12:41 AM
RE: I'm batting 1000 - by jerryhawthorne - 09-22-2015, 06:13 PM
RE: I'm batting 1000 - by Eric Adams - 09-22-2015, 07:24 PM
RE: I'm batting 1000 - by jerryhawthorne - 09-22-2015, 07:31 PM
RE: I'm batting 1000 - by jerryhawthorne - 09-22-2015, 07:35 PM
RE: I'm batting 1000 - by morzh - 09-22-2015, 10:09 PM
RE: I'm batting 1000 - by Arran - 09-23-2015, 01:36 AM
RE: I'm batting 1000 - by Eric Adams - 09-23-2015, 11:50 AM
RE: I'm batting 1000 - by Paul Philco322 - 09-24-2015, 07:57 PM
RE: I'm batting 1000 - by Eric Adams - 09-25-2015, 10:42 AM
RE: I'm batting 1000 - by TA Forbes - 10-10-2015, 11:10 AM
RE: I'm batting 1000 - by TA Forbes - 10-10-2015, 07:12 PM
RE: I'm batting 1000 - by Ron Ramirez - 10-10-2015, 09:16 PM
RE: I'm batting 1000 - by PAradiogeek - 10-11-2015, 01:15 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently no members online.

>