1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
I'm batting 1000
Eric Adams
Phorum Expert
*****
Posts: 825
Threads: 113
Joined: Aug 2012
City: The Villages State, Province, Country: Florida
#6

09-22-2015, 07:24 PM
Sure do, Jerry. I was able to do the IF alignment.
Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

Website Find
« Next Oldest | Next Newest »


Messages In This Thread
I'm batting 1000 - by Eric Adams - 09-21-2015, 11:17 PM
RE: I'm batting 1000 - by Steve Davis - 09-21-2015, 11:28 PM
RE: I'm batting 1000 - by Eric Adams - 09-22-2015, 12:18 AM
RE: I'm batting 1000 - by Steve Davis - 09-22-2015, 12:41 AM
RE: I'm batting 1000 - by jerryhawthorne - 09-22-2015, 06:13 PM
RE: I'm batting 1000 - by Eric Adams - 09-22-2015, 07:24 PM
RE: I'm batting 1000 - by jerryhawthorne - 09-22-2015, 07:31 PM
RE: I'm batting 1000 - by jerryhawthorne - 09-22-2015, 07:35 PM
RE: I'm batting 1000 - by morzh - 09-22-2015, 10:09 PM
RE: I'm batting 1000 - by Arran - 09-23-2015, 01:36 AM
RE: I'm batting 1000 - by Eric Adams - 09-23-2015, 11:50 AM
RE: I'm batting 1000 - by Paul Philco322 - 09-24-2015, 07:57 PM
RE: I'm batting 1000 - by Eric Adams - 09-25-2015, 10:42 AM
RE: I'm batting 1000 - by TA Forbes - 10-10-2015, 11:10 AM
RE: I'm batting 1000 - by TA Forbes - 10-10-2015, 07:12 PM
RE: I'm batting 1000 - by Ron Ramirez - 10-10-2015, 09:16 PM
RE: I'm batting 1000 - by PAradiogeek - 10-11-2015, 01:15 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4258 online users. [Complete List]
» 1 Member(s) | 4257 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)