I'm batting 1000

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

I'm batting 1000

Arran
Phorum Expert

Posts: 4,707
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA

#10

09-23-2015, 01:36 AM

Schematic linked to is an Air King 4705, not an Airline, or is your set actually an Air King? If so try replacing the 22k Ohm resistor on pin #1 of the 12SA7 tube. The 22K resistor, or R3, may test fine cold, but may not when the set is powered up.
Regards
Arran

Find

« Next Oldest | Next Newest »

Messages In This Thread

I'm batting 1000 - by Eric Adams - 09-21-2015, 11:17 PM

RE: I'm batting 1000 - by Steve Davis - 09-21-2015, 11:28 PM

RE: I'm batting 1000 - by Eric Adams - 09-22-2015, 12:18 AM

RE: I'm batting 1000 - by Steve Davis - 09-22-2015, 12:41 AM

RE: I'm batting 1000 - by jerryhawthorne - 09-22-2015, 06:13 PM

RE: I'm batting 1000 - by Eric Adams - 09-22-2015, 07:24 PM

RE: I'm batting 1000 - by jerryhawthorne - 09-22-2015, 07:31 PM

RE: I'm batting 1000 - by jerryhawthorne - 09-22-2015, 07:35 PM

RE: I'm batting 1000 - by morzh - 09-22-2015, 10:09 PM

RE: I'm batting 1000 - by Arran - 09-23-2015, 01:36 AM

RE: I'm batting 1000 - by Eric Adams - 09-23-2015, 11:50 AM

RE: I'm batting 1000 - by Paul Philco322 - 09-24-2015, 07:57 PM

RE: I'm batting 1000 - by Eric Adams - 09-25-2015, 10:42 AM

RE: I'm batting 1000 - by TA Forbes - 10-10-2015, 11:10 AM

RE: I'm batting 1000 - by TA Forbes - 10-10-2015, 07:12 PM

RE: I'm batting 1000 - by Ron Ramirez - 10-10-2015, 09:16 PM

RE: I'm batting 1000 - by PAradiogeek - 10-11-2015, 01:15 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio. This is a shame because this should be a good performer. 2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W 1.5k ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

Who's Online

There are currently 4052 online users. [Complete List]
» 2 Member(s) | 4050 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me