Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

An Interesting Philco Model
#3

I think it is a Fraken-Philco because normally all consoles or tables would have a back piece to support the side, in the case of a table I would expect some type of bottom but at least a rear lower brace. It looks like they chopped 41-624 but I am impressed with the quality of the work.


Messages In This Thread
An Interesting Philco Model - by Arran - 03-05-2009, 10:58 PM
Re: An Interesting Philco Model - by exray - 03-05-2009, 11:41 PM
Re: An Interesting Philco Model - by 49Stude63 - 03-05-2009, 11:50 PM
Re: An Interesting Philco Model - by Arran - 03-05-2009, 11:54 PM
Re: An Interesting Philco Model - by Arran - 03-06-2009, 12:02 AM
Re: An Interesting Philco Model - by Doug Houston - 03-06-2009, 12:58 AM
Re: An Interesting Philco Model - by Arran - 03-06-2009, 02:24 AM
Re: An Interesting Philco Model - by 49Stude63 - 03-06-2009, 05:33 PM
Re: An Interesting Philco Model - by Arran - 03-06-2009, 07:12 PM
Re: An Interesting Philco Model - by Ron Ramirez - 03-06-2009, 09:51 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
trying to identify this wire type
...and modern wire of the appropriate gauges and insulation V-rating (300V minimum, usually shown right on the wire) is ...morzh — 05:47 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
I have a question about this radio, is there anyone that has access to this radio that has an intact unmolested speaker ...captainclock1988 — 04:28 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Well what makes me confuse all of those companies is that all three of those companies (Setchell-Carlson, Stromberg-Carl...captainclock1988 — 04:21 PM
trying to identify this wire type
The red wire is rubber covered wire. The others are cotton braid over rubber often in colors or a tracer, also strand...Chas — 02:43 PM
trying to identify this wire type
Greetings Phorum members, Hope you can help me identify this type of wire in the photo I have attached.  I am not sure ...georgetownjohn — 01:53 PM
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM

[-]
Who's Online
There are currently 3120 online users. [Complete List]
» 1 Member(s) | 3119 Guest(s)
Avatar

>