1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
Philco PT-69 Question
Radioroslyn
Phorum Expert
*****
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

10-03-2015, 06:56 PM
Doesn't look like it. But since your a nice guy I'll give you the Terry's voltage chart:
35Z3 Pin 7 +100dc
35A5 pin 2&3 +90vdc  Pin 5 -8vdc.
7C6 pin 2 +80vdc
7B7 pin2&3 +80vdc
7A8 pin 2&3 +80vdc
Measure with the - meter lead connected to the - lead of the filter condersers
That's a good start, report back.
Is it raining down there yet???

GL
Terry
(This post was last modified: 10-07-2015, 05:15 PM by Radioroslyn.)
Find
« Next Oldest | Next Newest »


Messages In This Thread
Philco PT-69 Question - by Eric - 10-03-2015, 11:59 AM
RE: Philco PT-69 Question - by Radioroslyn - 10-03-2015, 06:56 PM
RE: Philco PT-69 Question - by Eric - 10-05-2015, 02:26 PM
RE: Philco PT-69 Question - by Radioroslyn - 10-05-2015, 05:48 PM
RE: Philco PT-69 Question - by Eric - 10-05-2015, 06:14 PM
RE: Philco PT-69 Question - by Radioroslyn - 10-07-2015, 05:14 PM
RE: Philco PT-69 Question - by OldRestorer - 10-09-2015, 06:53 PM
RE: Philco PT-69 Question - by Radioroslyn - 10-09-2015, 11:28 PM
RE: Philco PT-69 Question - by Eric - 10-22-2015, 07:06 PM
RE: Philco PT-69 Question - by Radioroslyn - 10-22-2015, 07:10 PM



Users browsing this thread: 3 Guest(s)
[-]
Recent Posts
Philco 38-7 Oscillation
Will do, thank you.tludka — 10:26 AM
Philco 38-7 Oscillation
As to your oscillation issue I would align the IF transformers. That may solve the problem. You also would want to check...Radioroslyn — 10:22 AM
Philco 38-7 Speaker
Thank you, I will check this out, I do have some shields I can place around the specific tubes. I searched the four que...tludka — 10:18 AM
Philco 38-7 Speaker
Also, check if any wires going to Grid Caps of the tubes that are supposed to be INSIDE of their respective shields (if ...morzh — 09:54 AM
Philco 38-7 Oscillation
Usually in this forum, when we discuss a radio, we do not multiply threads. You already have a thread on this. If you wa...morzh — 09:27 AM
identify very thin wire for replacement on 37-640
You can possibly use a heatshrink tubing. If you decide to replace the wire, anything gauge 24, 300V rated will do (it ...morzh — 09:25 AM
identify very thin wire for replacement on 37-640
Happy Thanksgiving,  I have attche a photo of a very thin wire with black plastic-looking insulation(some of it has com...georgetownjohn — 09:14 AM
Philco 60 Squealing
I got my signal tracer out to see if I could tell at what stage the squeal was coming from. It is present on the plate o...dconant — 09:07 AM
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM

[-]
Who's Online
There are currently 3219 online users. [Complete List]
» 2 Member(s) | 3217 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration