Philco PT-69 Question

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Philco PT-69 Question

Eric
Senior Member

Posts: 451
Threads: 85
Joined: Nov 2011
City: Cumming, GA

10-05-2015, 02:26 PM

(10-03-2015, 06:56 PM)Radioroslyn Wrote: Doesn't look like it. But since your a nice guy I'll give you the Terry's voltage chart:
35Z3 Pin 7 +100dc
35A5 pin 2&3 +90vdc Pin 5 -8vdc.
7C6 pin 80vdc
7B7 pin2&3 +80vdc
7A8 pin 2&3 +80vdc
Measure with the - meter lead connected to the - lead of the filter condersers
That's a good start, report back.
Is it raining down there yet???

GL
Terry

Terry
been away from it for a few days otherwise known as honey do list. We had about 6 days of rain here about 6" or so over those days, nice today!
My other issue is I have a 50A5 in place of the 35A5 I think it should work if every thing else is ok? I have a 35A5 on the way also have the dreaded rubber wire insulation issue.

Thanks
Eric

Find

« Next Oldest | Next Newest »

Messages In This Thread

Philco PT-69 Question - by Eric - 10-03-2015, 11:59 AM

RE: Philco PT-69 Question - by Radioroslyn - 10-03-2015, 06:56 PM

RE: Philco PT-69 Question - by Eric - 10-05-2015, 02:26 PM

RE: Philco PT-69 Question - by Radioroslyn - 10-05-2015, 05:48 PM

RE: Philco PT-69 Question - by Eric - 10-05-2015, 06:14 PM

RE: Philco PT-69 Question - by Radioroslyn - 10-07-2015, 05:14 PM

RE: Philco PT-69 Question - by OldRestorer - 10-09-2015, 06:53 PM

RE: Philco PT-69 Question - by Radioroslyn - 10-09-2015, 11:28 PM

RE: Philco PT-69 Question - by Eric - 10-22-2015, 07:06 PM

RE: Philco PT-69 Question - by Radioroslyn - 10-22-2015, 07:10 PM

View a Printable Version

Users browsing this thread: 2 Guest(s)

Recent Posts
Philco 38-7 Oscillation
Will do, thank you.tludka — 10:26 AM
Philco 38-7 Oscillation
As to your oscillation issue I would align the IF transformers. That may solve the problem. You also would want to check...Radioroslyn — 10:22 AM
Philco 38-7 Speaker
Thank you, I will check this out, I do have some shields I can place around the specific tubes. I searched the four que...tludka — 10:18 AM
Philco 38-7 Speaker
Also, check if any wires going to Grid Caps of the tubes that are supposed to be INSIDE of their respective shields (if ...morzh — 09:54 AM
Philco 38-7 Oscillation
Usually in this forum, when we discuss a radio, we do not multiply threads. You already have a thread on this. If you wa...morzh — 09:27 AM
identify very thin wire for replacement on 37-640
You can possibly use a heatshrink tubing. If you decide to replace the wire, anything gauge 24, 300V rated will do (it ...morzh — 09:25 AM
identify very thin wire for replacement on 37-640
Happy Thanksgiving, I have attche a photo of a very thin wire with black plastic-looking insulation(some of it has com...georgetownjohn — 09:14 AM
Philco 60 Squealing
I got my signal tracer out to see if I could tell at what stage the squeal was coming from. It is present on the plate o...dconant — 09:07 AM
Philco 16B Parts
The 16B's in the tombstone cabinet sport a 10 1/2" spkr vs the older cathedral sets which uses an 8". The p/p ...Radioroslyn — 12:58 AM
Philco 38-7 Oscillation
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 11:16 PM

Who's Online

There are currently 2304 online users. [Complete List]
» 3 Member(s) | 2301 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me