1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 1 Vote(s) - 3 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
my 37-61 the work...
mikethedruid
Banned
Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN
#4

10-09-2015, 12:18 PM
Beautiful job, but it is the tombstone model, and uses a different set of decals from the ones I had to use. The application would have gone quite smoothly if the size and alignment had been correct. The problems came because I had to keep trying to re-position the decal to get things to line up the best they could.I have no problem with the thickness of the decal material, personally. I just wish it had fit better.
Find
« Next Oldest | Next Newest »


Messages In This Thread
my 37-61 the work... - by mikethedruid - 09-27-2015, 04:00 PM
RE: my 37-61 the work... - by mikethedruid - 10-09-2015, 11:30 AM
RE: my 37-61 the work... - by OldRestorer - 10-09-2015, 11:53 AM
RE: my 37-61 the work... - by mikethedruid - 10-09-2015, 12:18 PM
RE: my 37-61 the work... - by mikethedruid - 10-11-2015, 04:58 PM
RE: my 37-61 the work... - by Ron Ramirez - 10-12-2015, 03:58 PM
RE: my 37-61 the work... - by mikethedruid - 10-13-2015, 04:50 AM
RE: my 37-61 the work... - by mikethedruid - 10-13-2015, 04:12 PM
RE: my 37-61 the work... - by mikethedruid - 12-10-2015, 06:46 PM
RE: my 37-61 the work... - by sam - 12-10-2015, 08:08 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM

[-]
Who's Online
There are currently 6090 online users. [Complete List]
» 2 Member(s) | 6088 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration