Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Dielectric insulators
#5

(10-14-2015, 10:31 AM)Radioroslyn Wrote:  Seems like your coil is ok but pot is bad. If you connect your antenna to the wiper of the pot do you receive signals ok? If so your pot is open. Suitable replacement would be one from 10K-50K.

Terry

Thanks again.  I will give it a try.  I am able to control the volume okay.  My body is acting like an antenna when I hold on to the volume control knob.  Like I mentioned before, the volume increases when I am holding the volume control knob, and decreases when I let go.  But I can raise and lower the volume okay otherwise. 

Any thoughts or ideas about what I can use for insulation material to replace the dielectric material in the sensitivity control?  It probably is the same material used in all of the old tuners for adjustments.  Looks like an early thin plastic material.

Here is another question maybe you can help with...I use a transmitter to listen to music on all of my AM radios.  The music comes in very clear.  I have 3 Philco cathedrals, a model 20, 80 JR and 81 JR.  Sound is distorted on all 3 from the transmitter, but clear on normal radio transmissions.  Is this normal on these older radios?  I have an AMT3000.  Maybe too powerful for the older radios? 

Thanks for any comments.

Jay


Messages In This Thread
Dielectric insulators - by Jay Thomas - 10-13-2015, 07:44 PM
RE: Dielectric insulators - by Radioroslyn - 10-14-2015, 08:53 AM
RE: Dielectric insulators - by Jay Thomas - 10-14-2015, 10:01 AM
RE: Dielectric insulators - by Radioroslyn - 10-14-2015, 10:31 AM
RE: Dielectric insulators - by Jay Thomas - 10-14-2015, 11:02 AM
RE: Dielectric insulators - by Radioroslyn - 10-14-2015, 12:25 PM
RE: Dielectric insulators - by Jay Thomas - 10-16-2015, 10:22 AM
RE: Dielectric insulators - by Jay Thomas - 10-14-2015, 03:12 PM
RE: Dielectric insulators - by Radioroslyn - 10-16-2015, 07:56 PM



Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
Tim, nice write up and thanks for sharing !! Sincerely Richardradiorich — 02:47 AM
HiFi (Chifi) tube amp build - but my own design.
Well, this was a real "Hum-Dinger" :lol: ! This will be kinda long, but hopefully it will help others having t...TV MAN — 01:55 AM
Shadow Meter Bulb
Phorum members, I am trying to find the bulb # for PHILCO Shadow Meter part number 45-2180 that is from a 37-640 chassis...georgetownjohn — 06:53 PM
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM

[-]
Who's Online
There are currently 7534 online users. [Complete List]
» 1 Member(s) | 7533 Guest(s)
Avatar

>