1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
my 37-61 project...
mikethedruid
Banned
Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN
#7

10-17-2015, 01:53 PM
Thanks, Mike, I already got the mounts from them. I think a little judicious use of sandpaper will make them fit quite nicely without any excessive squishing; one does want a BIT of squishing with rubber mounts, after all.
Find
« Next Oldest | Next Newest »


Messages In This Thread
my 37-61 project... - by mikethedruid - 09-26-2015, 04:12 PM
RE: my 37-61 project... - by mikethedruid - 09-30-2015, 03:29 PM
RE: my 37-61 project... - by mikethedruid - 10-02-2015, 05:44 PM
RE: my 37-61 project... - by mikethedruid - 10-05-2015, 06:40 PM
RE: my 37-61 project... - by mikethedruid - 10-17-2015, 12:03 PM
RE: my 37-61 project... - by KCMike - 10-17-2015, 12:56 PM
RE: my 37-61 project... - by mikethedruid - 10-17-2015, 01:53 PM
RE: my 37-61 project... - by mikethedruid - 11-16-2015, 07:23 PM
RE: my 37-61 project... - by mikethedruid - 11-16-2015, 11:51 PM
RE: my 37-61 project... - by klondike98 - 11-17-2015, 12:46 AM
RE: my 37-61 project... - by mikethedruid - 11-17-2015, 02:06 AM
RE: my 37-61 project... - by mikethedruid - 12-09-2015, 09:08 PM
RE: my 37-61 project... - by kiwi_steve - 12-10-2015, 12:07 AM
RE: my 37-61 project... - by mikethedruid - 12-11-2015, 08:38 AM
RE: my 37-61 project... - by mikethedruid - 12-12-2015, 11:10 PM
RE: my 37-61 project... - by mikethedruid - 12-14-2015, 07:38 PM
RE: my 37-61 project... - by mikethedruid - 12-27-2015, 07:22 PM
RE: my 37-61 project... - by mikethedruid - 12-27-2015, 10:38 PM
RE: my 37-61 project... - by mikethedruid - 12-28-2015, 12:53 AM
RE: my 37-61 project... - by klondike98 - 12-28-2015, 09:20 AM
RE: my 37-61 project... - by mikethedruid - 01-01-2016, 12:53 AM
RE: my 37-61 project... - by mikethedruid - 01-27-2016, 02:58 PM
RE: my 37-61 project... - by KCMike - 01-27-2016, 04:35 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Hi Bridcarl +1 on the others.  Pin 6 of the 7C6 is the AVC Diode so it is appropriate that that pin 4 of the coil con...MrFixr55 — 07:30 AM
462ron
Joseph, this is beyond awesome. A lot of thought and engineering went into this and you hit a home run! Now I must save ...462ron — 07:27 AM
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM

[-]
Who's Online
There are currently 3606 online users. [Complete List]
» 3 Member(s) | 3603 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration