Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco PT-69 Question
#9

Finally got back to it, also got the 35A5 but I had a problem to sort out mainly putting a cap end to the wrong place that's where your voltages helped me fined it and I replace some brittle wiring. The radio plays great so I decided to do a experiment. I put back in the 50A5 and the radio works pretty good almost no difference on the strong stations but the weaker ones were pretty much gone. 
Thanks for all the help when I get it together I will post a picture.

Eric


Messages In This Thread
Philco PT-69 Question - by Eric - 10-03-2015, 11:59 AM
RE: Philco PT-69 Question - by Radioroslyn - 10-03-2015, 06:56 PM
RE: Philco PT-69 Question - by Eric - 10-05-2015, 02:26 PM
RE: Philco PT-69 Question - by Radioroslyn - 10-05-2015, 05:48 PM
RE: Philco PT-69 Question - by Eric - 10-05-2015, 06:14 PM
RE: Philco PT-69 Question - by Radioroslyn - 10-07-2015, 05:14 PM
RE: Philco PT-69 Question - by OldRestorer - 10-09-2015, 06:53 PM
RE: Philco PT-69 Question - by Radioroslyn - 10-09-2015, 11:28 PM
RE: Philco PT-69 Question - by Eric - 10-22-2015, 07:06 PM
RE: Philco PT-69 Question - by Radioroslyn - 10-22-2015, 07:10 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco model 38 code 121 not receiving signal.
That's true. Of course If I were to get a vtvm I'd probably have to sink money in to it to get it working right. Probabl...Stormlord5500 — 08:44 PM
Philco model 38 code 121 not receiving signal.
A DMM is good enough. One rarely has to measure indictance, but if you do, short of getting a serious LCR meter (I hav...morzh — 07:35 PM
Testing a speaker and output transformer Trutone A2-G
You guy's are right on. I found a broken wire on the speaker plug that I replaced and all is well now. Have better volu...murf — 03:43 PM
Philco model 38 code 121 not receiving signal.
I need to get a vtvm. I think that little component tester is just more accurate. Plus it shows the inductance which is ...Stormlord5500 — 03:07 PM
Philco model 38 code 121 not receiving signal.
I use a pair of Mastercraft brand DMMs from Canadian Tire, from what I read most of those DMMs use the same main chip re...Arran — 02:36 PM
Philco model 38 code 121 not receiving signal.
Thank you sir. Yes I feel good and also relieved because this one's been weighing on me a bit.Stormlord5500 — 11:18 AM
Philco model 38 code 121 not receiving signal.
It feels good don't it? Good luck on the rest.Paul Philco322 — 11:06 AM
Philco model 38 code 121 not receiving signal.
I've reinstalled the coil. Now IT'S ALIVE!!!!!! I fired up my TinySA on signal generator mode and set it to 1400Kc and ...Stormlord5500 — 11:01 AM
Philco model 38 code 121 not receiving signal.
Yes, Walmart, right up there with Fluke.RodB — 11:00 AM
PT 6 chassis screws size???
it certainly won't be metric! SAE threads were all that was known then. Take care, - GaryGarySP — 10:58 AM

[-]
Who's Online
There are currently 1429 online users. [Complete List]
» 1 Member(s) | 1428 Guest(s)
Avatar

>