Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Just picked up a 41-295
#13

So I've continued on the recapping of it. Since it plays I've been changing one at a time. Replaced a .005 (.0047) between one of the 37's and a 42 and it went to ****. Bad new cap. It was one of the white ones from Mouser that I've had nothing but trouble with.

One interesting thing is both of the 7A4's and 7B7's test closer to dead than good, but the radio has great ears just using 1' of wire on terminal 2. I should stick in the cabinet and see how it does on the loop.

John
Las Vegas, NV USA


Messages In This Thread
Just picked up a 41-295 - by LASJayhawk - 04-27-2015, 07:18 PM
RE: Just picked up a 41-295 - by OldRestorer - 04-27-2015, 07:46 PM
RE: Just picked up a 41-295 - by John R - 04-27-2015, 07:51 PM
RE: Just picked up a 41-295 - by Phlogiston - 04-27-2015, 10:32 PM
RE: Just picked up a 41-295 - by mikethedruid - 04-29-2015, 06:41 PM
RE: Just picked up a 41-295 - by jerryhawthorne - 04-30-2015, 04:06 PM
RE: Just picked up a 41-295 - by LASJayhawk - 10-24-2015, 09:22 PM
RE: Just picked up a 41-295 - by LASJayhawk - 10-25-2015, 07:05 PM
RE: Just picked up a 41-295 - by John R - 10-26-2015, 04:40 PM
RE: Just picked up a 41-295 - by klondike98 - 10-25-2015, 09:54 PM
RE: Just picked up a 41-295 - by LASJayhawk - 10-26-2015, 08:36 PM
RE: Just picked up a 41-295 - by LASJayhawk - 10-26-2015, 08:41 PM
RE: Just picked up a 41-295 - by LASJayhawk - 11-01-2015, 10:28 PM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT 6 chassis screws size???
Hello bridKarl, that sounds right or maybe 8/32 . Sincerely Richardradiorich — 01:00 AM
PT 6 chassis screws size???
Have this done except for missing chassis screws. It looks like 1 inch 6/32 sheet metal screw may work but can anyone s...bridkarl — 10:32 PM
Philco model 38 code 121 not receiving signal.
Hello Stormlord, Well done on rewinding that coil it turned fairly good for your first one. Sincerely Richardradiorich — 09:12 PM
Philco model 38 code 121 not receiving signal.
Well here it is. It ain't pretty, but hopefully it'll work. I checked it with my DMM on continuity and it keeps and r...Stormlord5500 — 08:56 PM
Philco 42-345 Restoration/Repair
Yes, 57 is an electrolytic cap that should be 12 mfd 400 volts according to the parts list from the Phorum library schem...RodB — 06:01 PM
Philco 42-345 Restoration/Repair
Looks like if I am reading it correctly it looks like the silver capacitor#57 that appears to be a replacement is of a l...osanders0311 — 05:09 PM
Philco model 38 code 121 not receiving signal.
Thanks Arran. Yeah this plastic is pretty thin. It's a little thinner than the original stuff. It kinda reminds me of p...Stormlord5500 — 04:37 PM
Testing a speaker and output transformer Trutone A2-G
The equivalent of one short turn is basically the same as that of a shorted load. If it is the primary's turn, then the ...morzh — 03:53 PM
Testing a speaker and output transformer Trutone A2-G
I've never had an output transformer become shorted, the failure mode is usually an open primary, or in a center tapped ...Arran — 03:52 PM
Philco model 38 code 121 not receiving signal.
As long as the plastic sheeting isn't too thick, I think that the thickness of photographic film would be just about rig...Arran — 03:19 PM

[-]
Who's Online
There are currently no members online.

>