1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Linear Mode
zenith 6s27 restore/FINISHED!
Fred Taylor
Phorum Expert
*****
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
#10

11-08-2015, 08:29 AM
(11-07-2015, 10:21 PM)Eliot Ness Wrote:  Looks just like it rolled off the factory floor - no better and no worse.  That's the highest compliment I can give for a cabinet resto Icon_thumbup

Thank you Eliot for the complement , I try to do the best I can with with the tools I have, enjoying restoring these radios. I wish i had a full time job doing them Icon_e_biggrin . Thanks every body else for the kind words.
Find
« Next Oldest | Next Newest »


Messages In This Thread
zenith 6s27 restore/FINISHED! - by Fred Taylor - 11-01-2015, 06:17 PM
RE: zenith 6s27 restore - by TimC - 11-03-2015, 08:05 PM
RE: zenith 6s27 restore - by Fred Taylor - 11-04-2015, 07:56 PM
RE: zenith 6s27 restore - by Crist Rigotti - 11-04-2015, 11:12 PM
RE: zenith 6s27 restore - by jerryhawthorne - 11-05-2015, 04:42 PM
RE: zenith 6s27 restore/FINISHED! - by Eliot Ness - 11-07-2015, 10:21 PM
RE: zenith 6s27 restore/FINISHED! - by Fred Taylor - 11-08-2015, 08:29 AM
RE: zenith 6s27 restore/FINISHED! - by PhilcoJohn - 11-08-2015, 10:05 AM



Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 5197 online users. [Complete List]
» 3 Member(s) | 5194 Guest(s)
AvatarAvatarAvatar

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)