Precision E-200-C

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Precision E-200-C

Radioroslyn
Phorum Expert

Posts: 7,284
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#14

11-24-2016, 08:10 AM

(11-23-2016, 09:22 PM)Mondial Wrote: Hey Terry, those Chinese counters look real nice to add digital readout to some of my old boatanchor receivers.

How do you program in the IF offset? Do you need a computer interface or is it done with jumpers or with pushbuttons on the PCB?

It's pretty simple two small pushbuttons on the back of the pcb. No switches or interfacing to mess with. I know a HRO that is going to get one!

https://www.youtube.com/watch?v=1_neC5Z_wEg
It just takes a few minutes to figure it out the buttons/function.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Precision E-200-C - by Mike L - 09-17-2016, 06:48 PM

RE: Precision E-200-C - by KCMike - 09-17-2016, 08:50 PM

RE: Precision E-200-C - by Bradley Rush - 11-20-2016, 10:33 PM

RE: Precision E-200-C - by Bradley Rush - 11-21-2016, 12:34 AM

RE: Precision E-200-C - by Mike L - 11-21-2016, 07:49 PM

RE: Precision E-200-C - by KCMike - 11-21-2016, 10:44 PM

RE: Precision E-200-C - by Radioroslyn - 11-21-2016, 11:35 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 11:00 AM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 01:21 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 01:26 PM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 03:00 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 03:10 PM

RE: Precision E-200-C - by Mondial - 11-23-2016, 09:22 PM

RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 08:10 AM

RE: Precision E-200-C - by Mondial - 11-24-2016, 09:34 AM

RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 11:36 AM

RE: Precision E-200-C - by Mike L - 11-26-2016, 04:32 PM

RE: Precision E-200-C - by Mike L - 12-24-2016, 02:40 PM

RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 03:41 PM

RE: Precision E-200-C - by Mike L - 12-24-2016, 04:49 PM

RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 06:06 PM

RE: Precision E-200-C - by Mike L - 12-31-2016, 08:33 AM

RE: Precision E-200-C - by Radioroslyn - 12-31-2016, 11:55 PM

RE: Precision E-200-C - by Mike L - 01-01-2017, 04:27 PM

RE: Precision E-200-C - by JLuke - 07-27-2024, 11:33 AM

RE: Precision E-200-C - by DaleHCook - 07-28-2024, 10:29 AM

RE: Precision E-200-C - by RodB - 07-28-2024, 03:59 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Model 96 cabinet veneer
I can't figure out what the first step is, let alone the final step. I have tried copying pictures from my hard drive a...TGLager — 01:40 PM
Philco 38-2 Low Volume
I managed to get some more time on this. Hi Mr. FixIT, The radio has been recapped. Many of the resistors were rep...dconant — 01:39 PM
Philco 38-2 Low Volume
Thanks guys for the help. I started looking at these points but I have to quit for the day. I will be looking into this ...dconant — 12:23 PM
RCA WV-98c
Check out this crazy zero pot operation. Touching it drives it crazy. Its rubber tipped. Also the 6al5 has no negative v...daveone23 — 12:08 PM
Philco 38-2 Low Volume
If you check all of that and still have a problem (my first inkling would be one of the 6F6s) then look at the 6J5 phase...RodB — 10:44 AM
RCA WV-98c
Those will probably depend on teh switch combination. Could you list some that you see, their values and what they sh...morzh — 10:26 AM
Model 96 cabinet veneer
You are probably skipping the final step. Once you select the photos you want and they get downloaded, the system assign...RodB — 09:36 AM
RCA WV-98c
At this point, there is no input, just internal voltages Which are incorrect and not sure what they should be.daveone23 — 09:15 AM
Philco 38-2 Low Volume
Hi DConat, Generally, the lower the plate voltage the less negative the grid voltage has to be. Since the plates an...MrFixr55 — 09:27 PM
RCA WV-98c
If I had it in front of me, I would triy to trace the signal on one of the non-working functions. Try to trace and high...morzh — 08:21 PM

Who's Online

There are currently 1214 online users. [Complete List]
» 1 Member(s) | 1213 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me