Precision E-200-C

Thread Rating:

0 Vote(s) - 0 Average
1
2
3
4
5

Linear Mode

Precision E-200-C

Radioroslyn
Phorum Expert

Posts: 7,284
Threads: 268
Joined: Dec 2009
City: Roslyn Pa

#19

12-24-2016, 03:41 PM

I've got Sam's 200C apart it's a bit newer but looks like your wire goes to pin 7 of the 6AU6. This one has the osc tube mounted under the tuning cap not on the back of the BS. Be careful as there are things that look like resistors that have too many color bands they are rf chokes. Double check with the diagram.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry

Find

« Next Oldest | Next Newest »

Messages In This Thread

Precision E-200-C - by Mike L - 09-17-2016, 06:48 PM

RE: Precision E-200-C - by KCMike - 09-17-2016, 08:50 PM

RE: Precision E-200-C - by Bradley Rush - 11-20-2016, 10:33 PM

RE: Precision E-200-C - by Bradley Rush - 11-21-2016, 12:34 AM

RE: Precision E-200-C - by Mike L - 11-21-2016, 07:49 PM

RE: Precision E-200-C - by KCMike - 11-21-2016, 10:44 PM

RE: Precision E-200-C - by Radioroslyn - 11-21-2016, 11:35 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 11:00 AM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 01:21 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 01:26 PM

RE: Precision E-200-C - by Radioroslyn - 11-22-2016, 03:00 PM

RE: Precision E-200-C - by morzh - 11-22-2016, 03:10 PM

RE: Precision E-200-C - by Mondial - 11-23-2016, 09:22 PM

RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 08:10 AM

RE: Precision E-200-C - by Mondial - 11-24-2016, 09:34 AM

RE: Precision E-200-C - by Radioroslyn - 11-24-2016, 11:36 AM

RE: Precision E-200-C - by Mike L - 11-26-2016, 04:32 PM

RE: Precision E-200-C - by Mike L - 12-24-2016, 02:40 PM

RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 03:41 PM

RE: Precision E-200-C - by Mike L - 12-24-2016, 04:49 PM

RE: Precision E-200-C - by Radioroslyn - 12-24-2016, 06:06 PM

RE: Precision E-200-C - by Mike L - 12-31-2016, 08:33 AM

RE: Precision E-200-C - by Radioroslyn - 12-31-2016, 11:55 PM

RE: Precision E-200-C - by Mike L - 01-01-2017, 04:27 PM

RE: Precision E-200-C - by JLuke - 07-27-2024, 11:33 AM

RE: Precision E-200-C - by DaleHCook - 07-28-2024, 10:29 AM

RE: Precision E-200-C - by RodB - 07-28-2024, 03:59 PM

View a Printable Version

Users browsing this thread: 1 Guest(s)

Recent Posts
Model 96 cabinet veneer
I can't figure out what the first step is, let alone the final step. I have tried copying pictures from my hard drive a...TGLager — 01:40 PM
Philco 38-2 Low Volume
I managed to get some more time on this. Hi Mr. FixIT, The radio has been recapped. Many of the resistors were rep...dconant — 01:39 PM
Philco 38-2 Low Volume
Thanks guys for the help. I started looking at these points but I have to quit for the day. I will be looking into this ...dconant — 12:23 PM
RCA WV-98c
Check out this crazy zero pot operation. Touching it drives it crazy. Its rubber tipped. Also the 6al5 has no negative v...daveone23 — 12:08 PM
Philco 38-2 Low Volume
If you check all of that and still have a problem (my first inkling would be one of the 6F6s) then look at the 6J5 phase...RodB — 10:44 AM
RCA WV-98c
Those will probably depend on teh switch combination. Could you list some that you see, their values and what they sh...morzh — 10:26 AM
Model 96 cabinet veneer
You are probably skipping the final step. Once you select the photos you want and they get downloaded, the system assign...RodB — 09:36 AM
RCA WV-98c
At this point, there is no input, just internal voltages Which are incorrect and not sure what they should be.daveone23 — 09:15 AM
Philco 38-2 Low Volume
Hi DConat, Generally, the lower the plate voltage the less negative the grid voltage has to be. Since the plates an...MrFixr55 — 09:27 PM
RCA WV-98c
If I had it in front of me, I would triy to trace the signal on one of the non-working functions. Try to trace and high...morzh — 08:21 PM

Who's Online

There are currently 1215 online users. [Complete List]
» 1 Member(s) | 1214 Guest(s)

Login
Username:
Password:	Lost Password?
	Remember me