Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Would You touch this wi th a ten' pole?? I need my head examined!!!
#16

Can't speak for the ten foot pole, but I'm a six foot Pole and I wouldn't touch it!!  Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#17

If it's the xtal I found the guy is out of he mind! I sent a offer will see.

Terry
#18

Hey Sam,
Maybe shock treatment just might help ME!!!!
I do get a dose of it every once in while when I'm not paying attention.

Terry
#19

Arron says it works 
Will it fit in 5 gall bucket ?
Do you have battery charger  and steel ?
Let me know I will come over next Sunday 
With what you need and try 
Ps I'm only coming over to Video tape it so 
I can post on phorum Icon_twisted

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#20

Ya know I've never sat in a 5G bucket of Borax before!!! Sound like fun!!
Aren't you at work????

Terry
#21

Icon_lol Not you silly the chassis
Yes at work I get break time and lunch time 

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#22

(08-13-2015, 07:08 PM)Radioroslyn Wrote:  Ya know I've never sat in a 5G bucket of Borax before!!! Sound like fun!!
Aren't you at work????

Terry

 Washing soda, or baking soda, but it only works with steel or iron. I thought of trying Borax but I've never heard of anyone else doing that.
Regards
Arran
#23

Just cleaned a solid brass table lamp with my electrolysis bucket using washing soda and a deep cycle 12 volt battery.  It came out looking like new!  Did a much better job than buffing with Simichrome compound.  Take care, Gary

"Don't pity the dead, pity the living, above all, those living without love."
Professor Albus Dumbledore
Gary - Westland Michigan
#24

Wow, Terry: those are some rough project sets BUT that is the way to afford-ably get an uncommon set. The caveat is having the knowledge coupled with the "will do" to get it right. 

But I know you have large amounts of both qualities and will soon have 'em good as new.  
#25

I think I need a new coupling capacitor!!!
See ya in a few weeks!!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>