BIG SCOTT CONSOLE CABINET RESTORE
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 384
Threads: 22
Joined: Mar 2015
City: Waxahachie, TX
That will look great when you're done with it Fred!
Crist
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
I love the Scott Tasman cabinet - I think it is one of Scott's best looking sets. I probably should have held on to the AW 23 and Tasman that I had. Oh well, maybe after retirement, I'll pursue another....
Anyway, Fred, I am sure you will do your usual fine work with this one!
--
Ron Ramirez
Ferdinand IN
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 370
Threads: 102
Joined: Jul 2011
City: Calgary, AB, CA
Very nice Fred. I always like to see your work. I have not used the Mohawk grain filler.
I have used the kind that you spread on with flat spreader and wait until it is almost dry, then use the burlap.
is Mohawk similar in application?
Dan in Calgary.
Living in Calgary Alberta
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Hello Dan, I quess Mohawk is about the same in regards to application . I wipe it off with fresh burlap before it dries hard like wax a car. I let it haze over then wipe it smooth, then later sand it off with 240 after it has dried overnight, clean and smooth out the crevices as show in pictures, that also before it gets hard.
Posts: 4,109
Threads: 311
Joined: Nov 2013
City: Kings Park NY
It looks terrible!
I will surely take it off your hands ![Icon_lol Icon_lol](https://philcoradio.com/phorum/images/smilies/icon_lol.gif)
You will have to show me how you did the veneer. Veneer on large areas scares me....
Me
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
Posts: 765
Threads: 147
Joined: Aug 2012
City: Dallas, TX
Posts: 384
Threads: 22
Joined: Mar 2015
City: Waxahachie, TX
You are truly a craftsmen!
Crist
Posts: 1,872
Threads: 212
Joined: May 2015
City: Seattle
State, Province, Country: WA
Stunning! Thank you for all of the photos.
Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN
Users browsing this thread: 1 Guest(s)
|
Recent Posts
|
Cannot Adjust an IF Transformer’s cores
|
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM |
PT-6 antenna connections
|
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM |
Cannot Adjust an IF Transformer’s cores
|
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM |
PT-6 antenna connections
|
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4.
Yes, pin 6 of the 7C6 is...RodB — 07:34 PM |
bridkarl
|
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM |
Cannot Adjust an IF Transformer’s cores
|
Joseph, now you are an engineer!!RodB — 06:37 PM |
PT-6 antenna connections
|
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM |
Cannot Adjust an IF Transformer’s cores
|
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM |
PT-6 antenna connections
|
I seem to have lost my way on this PT-6.
I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM |
40-150 General questions
|
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM |
Who's Online
|
There are currently 4298 online users. [Complete List] » 1 Member(s) | 4297 Guest(s)
|
|
|
![>](https://philcoradio.com/phorum/images/bootbb/asb/right_arrow.png)
|