Thread Rating:
  • 1 Vote(s) - 1 Average
  • 1
  • 2
  • 3
  • 4
  • 5

I must have a soft spot for Philcos...
#1

...when I paid $32 for this 37-60. That's pink paint and I have no plans to restore that photo-finish. I'm going to reveneer the front with something interesting like curly maple. I'll take my scolding later.

[Image: http://i191.photobucket.com/albums/z309/...ckudmx.jpg]
[Image: http://i191.photobucket.com/albums/z309/...5ab4rn.jpg]
#2

Well, we all like a challenge now and then! Sometimes you just feel sorry for one and make it your mission to save it from the scrap heap. Go for it!
#3

You will take your scolding now!

Restore that photo-finish my good man...
It's not that hard....

Me

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#4

Quote:It's not that hard....
I hear you....barely.... Icon_wave .......I'll bring it to Kutztown and you'll be begging me to sell it to you Icon_eek .
#5

Not unless the photofinish is restored.. that is hard Icon_lol

Me

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#6

I'm in the process of restoring a 37-61, which uses the same cabinet as yours. I have bought the Re-Faux Pro decals for restoring the photofinish. I have written about it in the cabinet restoration section. I'll be applying the decals come spring, it is too cold in my house to do finishing work right now. If you wait until Spring, you can see how mine turns out, and decide what you want to do then. Believe me, the decals are a lot easier than trying to re-veneer the front. I already did it once, but the decals were off. I sent Tony my own cabinet so he could correct them perfectly, so hopefully they will be right now. The curved trim lines on the curved part of the speaker grill, and the 3 center light color trim stripes were off before, now they should be right.
#7

Do it right! You'll regret it later. My 37-665B will be a challenge but well worth the effort.
#8

I agree, It really would be worth waiting and doing it up right, actually easier too.
#9

Do it, you are thinking the way I was not replace the photo finish, go for it . Here are a few of my examples.


Attached Files Image(s)
               
#10

I used paper on mine.

I printed high res photos of the veneers and glued them on. Came out pretty D**n nice.... I want to try my hand at had restoring it with paints but my hands are not so hot these days... Icon_sad

Anything is Better than this...


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#11

What is that, a radio or a guitar body? Icon_thumbdown

--
Ron Ramirez
Ferdinand IN
#12

Icon_lol

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#13

(02-16-2016, 11:14 AM)Ron Ramirez Wrote:  What is that, a radio or a guitar body? Icon_thumbdown

 Old Foggy on fleabay must have got his hands on that thing.




Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM

[-]
Who's Online
There are currently 6812 online users. [Complete List]
» 1 Member(s) | 6811 Guest(s)
Avatar

>