Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 46-1201 really it followed me home!
#1

Yup, any more Philcos and I'll have to find a dealer sign to hang on my front door!
Again as in my other finds it is unmolested and original. Wait a minute, the power cord has been patched.
Glad I retired to a life of leisure Icon_lol to a hobby of restoring old radios.
#2

Those are cool little players! My wife has a photo of her grandmother sitting next to one. I'd like to get one someday but I'll wait for the right deal.
#3

They are quite heavy to ship. Figure around $40 at a minimum, which can add a lot to the final cost if you go the eBay route to find one (and there are always examples on there available). There's one on there right now with a BIN for $29.95...with $49 shipping. I'm NOT advertising it, just citing it as an example of how shipping on one of these can cost almost twice as much as the radio itself!

Greg V.
West Bend, WI
Member WARCI.org
#4

Isn't it funny that the cost of fuel has gone down quite a bit, yet the cost of shipping keeps going up? Icon_thumbdown

--
Ron Ramirez
Ferdinand IN
#5

Very true, Ron. I sent a media DVD...in a paper sleeve and bubble wrap envelope...to a friend in the UK a few weeks ago. It weighed practically nothing, and I used to be able to send these to him for only a few dollars using small packet rate. The cheapest rate now was $13!!

Getting back to the 1201's, I once found one in pretty rough shape on eBay for $10 or best offer. Shipping was $20 (at the time). I offered the seller $1.00 for the set and they accepted. It was the "somewhat" harder to find 48-1201 (9 times out of 10 you're going to find a 46-1201 because there were SO many more produced under that model number during 1946-47).

Greg V.
West Bend, WI
Member WARCI.org




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM
Hickok AC51 tube tester
Cleaned ann contacts, switches and sockets, works great now.martinj — 11:32 AM
Model 28L
Hello, I'm restoring a Philco 28L and the output transformer is open. Part number of the transformer is 32-7020. Can...HORSTE — 10:32 AM
Philco 42-1008 conversion kit
I read about a kit to convert the variable speed changer in the Philco 42-1008 into a single speed unit.  That would rem...alangard — 09:30 PM

[-]
Who's Online
There are currently 6148 online users. [Complete List]
» 1 Member(s) | 6147 Guest(s)
Avatar

>