1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Rebuild Crystal Phono Cartridge Philco 41-605
markmokris
Member
***
Posts: 109
Threads: 18
Joined: Mar 2015
City: Ann Arbor, Michigan
#1

03-13-2016, 01:07 AM
I have a dead original crystal phono cartridge from a Philco 41-605. I need to have it rebuilt. I have read Syl's tutorial on doing this oneself, and I really don't want to attempt it.

Where can I send the cartridge to pay someone to rebuild it for me?

Thanks,

Mark K8KZ
Find
Eliot Ness
Phorum Expert
*****
Posts: 3,135
Threads: 54
Joined: Apr 2011
City: Lexington, KY
#2

03-13-2016, 10:39 AM
As I mentioned earlier West-Tech is the only place I know about.  However, Kirk (OldRestorer) has recently announced he has successfully rebuilt a cartridge or two and is even growing his own crystals.  Maybe give him a shout and see if he's ready to take on a trial customer.

http://www.philcoradio.com/phorum/showth...?tid=14111
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
(This post was last modified: 03-13-2016, 11:42 AM by Eliot Ness. Edit Reason: added link )
Find
markmokris
Member
***
Posts: 109
Threads: 18
Joined: Mar 2015
City: Ann Arbor, Michigan
#3

03-14-2016, 12:48 PM
(03-13-2016, 10:39 AM)Eliot Ness Wrote:  As I mentioned earlier West-Tech is the only place I know about.  However, Kirk (OldRestorer) has recently announced he has successfully rebuilt a cartridge or two and is even growing his own crystals.  Maybe give him a shout and see if he's ready to take on a trial customer.

http://www.philcoradio.com/phorum/showth...?tid=14111

John,

This morning I contacted West-Tech and Gib sent me an email saying they would rebuild it for $50.  So I think I will go that route.

Thanks,

Mark K8KZ
Find
Eliot Ness
Phorum Expert
*****
Posts: 3,135
Threads: 54
Joined: Apr 2011
City: Lexington, KY
#4

03-14-2016, 01:39 PM
Quote:This morning I contacted West-Tech and Gib sent me an email saying they would rebuild it for $50.  So I think I will go that route.

Good luck Mark and let us know how it turns out.
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco Model 80 Transformer resistance
Just forget this number, it is useless anyway. Simply proceed with your project.morzh — 10:08 PM
Philco Model 80 Transformer resistance
My $0.02 is that it is a misprint. I tried to look up the value for the similar 84 and 37-84, and ther is no resistance...MrFixr55 — 09:51 PM
Philco Model 80 Transformer resistance
Thanks for the quick reply! Hmm...well that's good, so what am I seeing that's 1042 ohms on the schematic for the pow...Mike L — 08:46 PM
Philco Model 80 Transformer resistance
The DC resistance of the primary is 8 to 9 Ohm.morzh — 07:54 PM
Philco Model 80 Transformer resistance
I have a feeling the primary winding on the power transformer is bad. My resistance reading on the primary side is 9 ohm...Mike L — 07:48 PM
Rusty Tuning Condenser
I would try Naval Jelly and use a soaked pipe cleaner to get it where it needs to go.RossH — 06:56 PM
38-10T chassis Restoration begins
Hello Dconant , they sold mica to use as a insulator between transistors and their heatsinks too. Rob I will remove th...radiorich — 02:52 PM
38-10T chassis Restoration begins
Thanks for the info guys. I always wondered why the use of mica. Now I know.dconant — 01:52 PM
38-10T chassis Restoration begins
Most common plastics have a dielectric constant in the 3-4 range whereas mica is around 6. This means that even if you w...Steve D — 01:46 PM
38-10T chassis Restoration begins
It is acceptable but not desirable. Plastic is not an approved cap dielectric, and even though a reasonably thick piece...morzh — 11:52 AM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration