1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Tube Shield Finish
Derek D
Junior Member
**
Posts: 25
Threads: 10
Joined: Dec 2005
#1

01-04-2006, 11:24 AM
Does anyone know what the original finish was on the square tube shields used on 620's and 630's? Were they plated like the chassis?

Mine are in pretty rough shape, and I want to make them look original.

Thanks,
Derek
Find
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

01-05-2006, 12:49 PM
The original finish was a shiny metal, but turns very dull over the years. Occasionally I see some tube shields that have managed to retain their original shine and the difference is quite astounding, frankly.
--
Ron Ramirez
Ferdinand IN
Find
Derek D
Junior Member
**
Posts: 25
Threads: 10
Joined: Dec 2005
#3

01-05-2006, 12:59 PM
I thought they were supposed to be shiny. Must have been some type of plating. Maybe nickel?
Find
49Stude63
Member
***
Posts: 225
Threads: 14
Joined: Oct 2005
City: Grand Blanc, Michigan
#4

01-05-2006, 01:40 PM
I have some that have retained most of their original non-corroded finish and they are a bright nickel/zinc type plating. I would think a spray finish that was fine aluminum or had a nickel type appearance would be ok. Some of mine are faded/corroded not from water exposure but probably from being handled, anything close would look better.
Find
Terry Judkins
Member
***
Posts: 91
Threads: 5
Joined: Oct 2005
City: Atlanta GA
#5

01-05-2006, 10:06 PM
Spray 'em with bright aluminum paint... Icon_twisted
Kind regards,
Terry
http://home.comcast.net/~suptjud/
"Life is simpler when you plow around the stump."
Website Find
Guest
Unregistered
 
#6

01-06-2006, 02:46 AM
Or spray them with hammertone gold.. Icon_lol
Hey,just a little Zenith joke!...OW...OWW!!
« Next Oldest | Next Newest »




Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM
Shadow Meter Bulb
Mike is correct on the bulb connection, two separate circuits. I found that by rotating the bulb and sliding it forward ...RodB — 12:19 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration