Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Tubes and More AM transmitter kit
#1

Built the Tubes and More AM transmitter kit and am enjoying learning the little fella's capabilities. Anyone else who has built this kit, please give me some pointers to optimize it's performance.

thanks
Frank

[Video: https://youtu.be/Bjh_hoSWQV8]

HE>i
#2

 Sounded pretty good to me Frank and your radio looks good also. I have an SSTran AMT 3000 I built couple of years
ago. It does a good job. I don't know about the one you built but someone on here probably does and can make suggestions about tweaking it for best performance.
#3

Found one in the box that I picked up at an auction a yr or so ago. Knew it was a broadcaster but didn't know it was an AES product till I saw it in there catalog a  month ago.
Did try it out. Has great coverage with no ground and just an antenna. No ground loop hum. The only issue is the audio quality could be a bit better.
With this type of transmitter(using a pentagrid tube) there can be some interaction between the oscillator and modulator causing frequency shift with the audio (part of the signal is AM but there can be some FM component to the signal too) which is undesirable.
I did play with it a little added a transformer the match the impedance from the computer out (low Z) to the input grid (high Z) and some loading. Wanted to try adding a little bias to the input to see if that will improves the audio but can't seem to find my little adjustable power supply.

Terry
#4

You can try changing the value of the cathode resistor to improve the modulation quality. This will effectively change the grid bias and locate the operating point of the tube on a more linear part of the curve. This graph is for the 6BE6, but the 6SA7 is very similar

[Image: http://www.wa2ise.com/radios/6be6g3.jpg]


I read somewhere that changing the resistor from 1 K to 500 ohms results in improved audio, or you can substitute a 1K pot and adjust for best output and quality.

This site goes into a lot of detail on the basic circuit and how it can be improved with negative feedback, etc.

http://www.wa2ise.com/radios/amxmit.html
#5

Tnx for the link. Will give it a try.
Will we get a chance to have an
eyeball in a week and a half??

Terry
#6

(04-28-2016, 12:49 PM)Radioroslyn Wrote:  Tnx for the link. Will give it a try.
Will we get a chance to have an
eyeball in a week and a half??

Terry

??

HE>i
#7

I think Terry was talking to Mondial.

--
Ron Ramirez
Ferdinand IN
#8

+1

Terry
#9

Hi Terry,

I guess you are referring to Kutztown. Sorry to say I will not be there. Its the same weekend my daughter is coming home from college. 
#10

(04-28-2016, 03:25 PM)Ron Ramirez Wrote:  I think Terry was talking to Mondial.

Hijackers...Thanks for the replies though.

HE>i




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Restore Code ??
Can someone tell me if my 42 tubes are connected triode or pentode in fixed or cathode bias? How could I tell by looking...dconant — 10:47 AM
Philco 40-120C Restoration
Hello David, that is great news about the tubes source being local ! Sounds like you got good start on the radio . ...radiorich — 09:41 AM
An attempt to remove the Field Coil from a G speaker
Mike; I've only run into a speaker with an open filed coil twice, and they were on newer speakers from the 1940s. One ...Arran — 12:48 AM
An attempt to remove the Field Coil from a G speaker
Arran Yes, this is my plan for now and what do I got to lose, this is not even the speaker from this radio, but one o...morzh — 10:44 PM
An attempt to remove the Field Coil from a G speaker
Mike;  I would unwrap the field coil, and see if maybe there a break near one of the ends, like where the coil wire att...Arran — 10:23 PM
An attempt to remove the Field Coil from a G speaker
...and this is what I did. I fed a little LT into the screwholes with a small brush, and a little on the rim next to the...morzh — 09:52 PM
Philco 40-120C Restoration
I combined the two 40-120C threads together as we like to keep the discussion of the same radio together. It helps with...klondike98 — 09:36 PM
Philco 40-120C Weak, Distorted Ouput
Just checked were I buy tubes price is four dollars. So living in Florid we have a local source for tubes. David    David — 09:14 PM
Philco 40-120C Weak, Distorted Ouput
The higher voltage may be due to higher mains voltage. My mains run 120-125AC when the set was new mains would be 110-11...David — 09:09 PM
Philco 40-120C Weak, Distorted Ouput
Thank you for your reply. I pulled a speaker from a Philco 41-221 and received the same result. I used a signal tracer t...bluecap — 08:45 PM

[-]
Who's Online
There are currently no members online.

>