Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Which set would you prefer?
#1

The 40-201X or the 41-300??

The chassis look pretty similar. The '201 has a rf amp stage where the '300 has two IF stages. '201X has a pentagrid converter '300 a dual triode set up. Audio stages look the same no SG inversion and conventional p/p pentode connected pentodes. Did a rough calculation to find that the 80 tube is running at full till( a little surprised that it isn't a 5Z3)

Would think it would be pretty close in performance but haven't had either one. Personally like the well louvered '300 cabinet a bit better looks powerful and have a line on one.

Terry
#2

I've owned both, and regretted letting both go.

The 41-300 seemed to be a bit better, both in terms of performance and audio output. But sooner or later, all of that bent veneer is going to start cracking, I think...

What I think would really be nice would be a 41-300/295/315 chassis and the accompanying 14 inch speaker in a 40-201X cabinet (which had a 12 inch speaker). Sure, it would be a Phranken-Philco, but to me would represent the best of both worlds (better looking cabinet...in my opinion...and better performance).

--
Ron Ramirez
Ferdinand IN
#3

You are getting the 300 old boy...
I been holding it long enough Icon_lol

ME

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#4

Well, there you go, Terry. Icon_lol

--
Ron Ramirez
Ferdinand IN




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
Outstanding work indeed. I wish I could come up with solutions like this.slford310 — 11:16 PM
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM

[-]
Who's Online
There are currently 3991 online users. [Complete List]
» 2 Member(s) | 3989 Guest(s)
AvatarAvatar

>