Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
If anyone is interested, I just posted a pictorial of this much despised chassis being rebuilt on my blog:
http://www.russoldradios.com/blog
Most people hate it. Not because it works poorly but because it is very difficult to work on. I have done several of these since they were used with a few changes for 2 years in many RCA and GE (Westinghouse?) radios. The same chassis was used in consoles and table models with the same speaker. There were also 7 and 9 tube versions.
Russ
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
Very nice job Russ.  That is a fine looking cabinet also.
I almost bought one similar awhile back but was out bid at the local club auction. Good to see what all is involved if ever I get one.
Posts: 3,148
Threads: 56
Joined: Apr 2011
City: Lexington, KY
Nice job Russ! Those tips will come in handy when I finally tackle a G.E. J100 cathedral I've been putting off for years.
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Posts: 5,160
Threads: 273
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
Posts: 4,429
Threads: 418
Joined: Jun 2011
City: Boston
State, Province, Country: Massachusetts
With the tuning condensor underneath it is busy under there, many of those RCA are toughies, RCA 28P is loved and hated too.
Nice work kid.
Paul
Tubetalk1
Posts: 4,858
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
They aren't that bad, I've worked on a couple of these, and will work on a couple more that are in the restoration docket. One was a C.G.E J-82 and the other a Canadian Westinghouse 801 Columaire which uses similar circuitry and components but in a Westinghouse built chassis, the next two will be another J-82, and an S-42A. The biggest nuisance isn't the tuning condenser it's the IF cans and the oscillator coil, which you may or may not have to remove to get at some things. These sets are good performers though, which probably explains why there are so many survivors as they were probably good sellers.
Regards
Arran
(This post was last modified: 07-16-2016, 04:23 AM by Arran.)
Posts: 157
Threads: 12
Joined: Dec 2012
City: Seattle, WA
Wow Russ, hard to believe that's the same radio!
What's your take on casting 2W resistors into dogbone molds? Are they still able to dissipate 2W, or are they derated a bit?
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
(07-16-2016, 04:28 AM)palegreenthumb Wrote: Wow Russ, hard to believe that's the same radio!
What's your take on casting 2W resistors into dogbone molds? Are they still able to dissipate 2W, or are they derated a bit?
I have been doing this for years now. I have only had one get hot enough to damage the molded material and it was the result of another failure. The idea is that you replace a 1/2w with a 2W or larger to better dissipate any heating, most of which leaves by way of the leads anyway.
But, yes. I would not run them at 2w. I have used 3.8w wire-wound when I thought heat would be a problem. This increases the cost by about 10X. These resistors (the ww) are the same size as a 2w metal (blue) so are sized to cast into a 1/2w dogbone or larger.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
(07-16-2016, 04:22 AM)Arran Wrote: They aren't that bad, I've worked on a couple of these, and will work on a couple more that are in the restoration docket. One was a C.G.E J-82 and the other a Canadian Westinghouse 801 Columaire which uses similar circuitry and components but in a Westinghouse built chassis, the next two will be another J-82, and an S-42A. The biggest nuisance isn't the tuning condenser it's the IF cans and the oscillator coil, which you may or may not have to remove to get at some things. These sets are good performers though, which probably explains why there are so many survivors as they were probably good sellers.
Regards
Arran
Removing the tuning cap allows access to the IF cans. One IF can cap can be removed by slightly distorting the front and back flanges of the chassis to get it past the coil. This also allows access to the tabs at the base of the cap can which must be bent to remove the can.
Another tip: When removing the cap can also remove or loosen the mount for the ceramic padder cap or you will break it with one of the tabs.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
(This post was last modified: 07-16-2016, 11:04 AM by Phlogiston.)
Posts: 4,858
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
Russ;
Just a thought on that wire wound that's on the resistor board, I looked up the set and found out that there was a 3 Watt carbon resistor in that position according to the parts list. It may have been replaced by a service man or it may have been a production change since it looks like they shrouded it in fish paper, either way putting a 5 Watt wire wound in it's place was a smart move.
Regards
Arran
Posts: 2,118
Threads: 112
Joined: Jun 2010
City: Medford OR (OR what?)
(07-18-2016, 03:13 AM)Arran Wrote: Russ;
Just a thought on that wire wound that's on the resistor board, I looked up the set and found out that there was a 3 Watt carbon resistor in that position according to the parts list. It may have been replaced by a service man or it may have been a production change since it looks like they shrouded it in fish paper, either way putting a 5 Watt wire wound in it's place was a smart move.
Regards
Arran
Yes, I believe all of that is true. The fish paper is factory installed.
"I just might turn into smoke, but I feel fine"
http://www.russoldradios.com/
Users browsing this thread: 2 Guest(s)
|
|
Recent Posts
|
|
Philco 42-345 Restoration/Repair
|
| Today I've been reading through the site trying to learn more about this radio. I also soldered the lose power cord cabl...osanders0311 — 08:24 PM |
|
Philco 610B oscillator wiring
|
| Thanks David! I do have that same later prodution model 610 schematic. I've also studied the Philco service bulletins fo...Tubester — 08:12 PM |
|
Philco 610B oscillator wiring
|
| Some info from Beitmans says late production. David David — 06:06 PM |
|
Restoring Philco 96
|
| Oh wow! Just found this thread. Brings me back to early days on this phorum. I did a 96 back in 2017. Thread here:
...rfeenstra — 06:05 PM |
|
Philco 610B oscillator wiring
|
| Thanks for the replies. It's not the really the hum that I am after. Just trying to understand why only the shortwave ba...Tubester — 04:01 PM |
|
Restoring Philco 96
|
| 70 and 90 are Superhets, but at least the 2x45 model of 90 uses the Plate detector (and so does 70).
Also the Atwaters,...morzh — 03:28 PM |
|
Restoring Philco 96
|
| Morzh, Prayers for your mom. I am sure that there was enough pain living through the Holocaust as a child. I pray dail...MrFixr55 — 02:19 PM |
|
Philco 610B oscillator wiring
|
| Hi Dan,
Divide and conquer. First off trry to differentiate between 60Hz and 120 Hz hum. 120 Hz hum has a higher pit...MrFixr55 — 01:49 PM |
|
Restoring Philco 96
|
| Yes, other than takin a toll on your back, they are undeed way more repair friendly than many other Philcos.
To me, som...morzh — 01:04 PM |
|
Philco 610B oscillator wiring
|
| If the wires look like they were this way from the factory (very neat and very dull soldering joints), I'd leave them be...morzh — 12:58 PM |
|
Who's Online
|
There are currently 2452 online users. [Complete List]
» 2 Member(s) | 2450 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
