Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Philco 90 arch veneer
#1

I have learned that the arches of the Philco 90 cathedral were made with oriental wood veneer; any idea where I might be able to acquire some of this? Or what might be a suitable substitute? Thanks,
Doc
#2

I am not sure there was any veneer...at least on some of them it looks like a plain stained plywood.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Correction- the fronts of the arches. It is definitely covered in a veneer because one of my arches is missing about half of it. In a post from 6-18 one of the posters said the veneer was "oriental wood"  so that was my clue.
#4

The sales literature is often a good source of information about the type of wood veneer used.

In the case of the Philco 90 cathedral we can look to the 1931 sales card flip book:
http://philcoradio.com/phorum/showthread.php?tid=13735

   

So you're on the right track with 'oriental wood'. Maybe this?
http://www.oakwoodveneer.com/oriental-wood-veneer.html

"Oriental Wood Veneer is a walnut-like wood with darker stripes and a hint of red and some figure. It is also known as Australian Walnut and Queensland Walnut."
#5

I think Mike is talking about the rear arch, Doc is talking about the front arch. Maybe????

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

Yes, you're right Terry.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#7

Sorry, Mike. I didn't specify front arch. I wasn't even thinking about that rear. Yeah, it's just plywood. And Nathan , thanks for the info.
Doc
#8

PM sent.

Steve

M R Radios   C M Tubes
#9

Problem solved!




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 5335 online users. [Complete List]
» 1 Member(s) | 5334 Guest(s)
Avatar

>