Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Could these tubes be the originals?
#1

I have a Philco 66 on the bench. While testing the tubes, I noticed that ALL were branded PHILCO and had similar appearance and date codes. I had no luck on finding information on the web for early Philco tubes. This radio had had some servicing (volume control, line bypass cap) but was otherwise all original.

I was wondering if the tubes were the originals as shipped? All the codes are arranged vertically, with a LETTER and a NUMBER. The codes I found were (first figure on TOP) 78: 5C, 6A7: H5, 75: C5, 42: B4, 80: B4. Looks like a month (letter) and year (number) - but just guessing.

Does anyone have a reference on-line? I do NOT have Lud's book.

Thanks,
Dave
#2

The number is the last digit of the year. Letters are months: C is January, B is October and H is February. After September 1935 the month codes changed: B is February, C is March, H is August.

In either case it seems odd to have dates so far apart (I'm quite sure Philco did not stockpile tubes for months).

These are Sylvania codes, and it's possible Philco bought tubes from someone else, which would have different codes.
#3

Is this information in the book Tube Lore or another source? It is just curious that at least the YEAR is close to the introduction date of the radio. I would not suspect that the tubes would have been changed so soon. And they are all branded Philco.

Thanks!




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4565 online users. [Complete List]
» 1 Member(s) | 4564 Guest(s)
Avatar

>