Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Unknown Gilfillan Model
#16

And here is a shot of the chassis with the re-stuffed caps in place, and the new cord installed.

[Image: https://farm5.staticflickr.com/4289/3506...46d8_b.jpg]

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
#17

I attached a spool of antenna wire. I slowly powered it up on the variac, and didn't get anything, then I realized the variac wasn't plugged in.  Icon_crazy
I plugged it in, and tried again. I wasn't sure which thumbscrew to attach the antenna to. 1st attempt, I got audio, but no radio signals, so I powered down and tried the other screw. Upon power-up, I immediately got static, so I dialed across the band. Everything came in on the dial where it should, so I didn't perform an alignment. For this video, I attached a 12 foot length of wire, and plugged it into my outside wire which runs 50-75 feet out in the backyard. This is a little cheap 4-tuber, so it doesn't have AVC. It's really obvious as I tune across the dial....

[Video: https://youtu.be/ewMVZBNpLPw]

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
#18

I dont remember this one...
I like it!
And you already have it going!
Slow down buddy, You might get a ticket at that speed Icon_lol
Me

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#19

Since I'm fixing the images from Photobucket, here's an update: A "studio shot" of it all back together and done.

[Image: https://farm5.staticflickr.com/4298/3587...317c_b.jpg]

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
#20

A++

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#21

Looks good Jeff Icon_thumbup 

Since you live in CA you should buy a set of Floyd Paul's 3 booklets,

Los Angeles Radio Manufacturing, The First Twenty Years:

http://www.antiqueradios.org/paul-bks.html


You might find a picture of your set in one of his books, they're very informative.

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#22

(07-12-2017, 12:42 PM)Eliot Ness Wrote:  Looks good Jeff Icon_thumbup 

Since you live in CA you should buy a set of Floyd Paul's 3 booklets,

Los Angeles Radio Manufacturing, The First Twenty Years:

http://www.antiqueradios.org/paul-bks.html


You might find a picture of your set in one of his books, they're very informative.
Thanks! I'll keep this in mind Icon_thumbup . I also have a slimly documented Flint that came out of the same factory. Icon_biggrin

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM
Philco 91 Speaker Replacement
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM
Philco 91 Speaker Replacement
I was wondering if I could use a more common Philco speaker and just add the resistance I need for the coil and get a ne...dconant — 07:45 AM

[-]
Who's Online
There are currently 2492 online users. [Complete List]
» 2 Member(s) | 2490 Guest(s)
AvatarAvatar

>