1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 42-1010 Veneer - European Walnut?
AVSorrell
Member
***
Posts: 76
Threads: 18
Joined: Nov 2015
City: Palmyra State, Province, Country: Virginia
#1

10-01-2016, 09:13 AM
Hi Guys -

I have a Philco 42-1010 that has some lost veneer that I am going to replace. One the below photo it is the area on the front below the grille that looks obvious in its veneer loss. Anyhow I gently pulled some more of the loose stuff off to look at the back. Is this the European walnut veneer Philco liked to use?  I will attach some photos below. Thanks for the advice! -- Andy

https://flic.kr/p/MHPRau
Full Radio

https://flic.kr/p/MDrf2M
Close up of Area

https://flic.kr/p/LPqm6H
finished side on veneer

https://flic.kr/p/MAM5Hq
unfinished side
Andy Sorrell
Palmyra, Virginia
(This post was last modified: 10-01-2016, 09:18 AM by AVSorrell.)
Find
Arran
Phorum Expert
*****
Posts: 4,686
Threads: 51
Joined: Sep 2008
City: Sandwick, BC, CA
#2

10-03-2016, 02:49 AM
 It's French Walnut, regular cut I think, sometimes Philco cabinets used quarter sawn French walnut but that is very straight grained. Have a look on fleabay if you need some, though you may have to buy 15 square feet of it or more.
Regards
Arran
Find
AVSorrell
Member
***
Posts: 76
Threads: 18
Joined: Nov 2015
City: Palmyra State, Province, Country: Virginia
#3

10-06-2016, 11:26 AM
Thanks Arran!
Andy Sorrell
Palmyra, Virginia
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently 2802 online users. [Complete List]
» 1 Member(s) | 2801 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration