1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Philco 42-355
Guest
Unregistered
 
#1

09-02-2009, 10:57 AM
I need a dial bezel for this radio. Any suggestions?
Ron Ramirez
Silent Key
*****
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand State, Province, Country: Indiana
#2

09-02-2009, 01:00 PM
Larry Bordonaro at Old-Time Replications.

http://www.antiqueradioknobs.com/

If you do not have your old escutcheon, you will have to come up with the brass insert above the knobs that reads VOLUME, BASS, TREBLE, TUNING. Otherwise you can remove the old insert from your old escutcheon and install on the repro.

Larry's repro escutcheon will be better then new overall, and looks just like the originals - but without the shrinkage, cracks and breaks!
--
Ron Ramirez
Ferdinand IN
Find
Raleigh
Senior Member
****
Posts: 347
Threads: 34
Joined: May 2007
City: Raleigh, NC
#3

09-06-2009, 08:17 PM
Radio Daze offers a reproduction of the 1942 brass insert, but it is made of plastic coated with some metallic finish to look like brass. I think they told me it sticks in place with some double-stick adhesive. I have never seen one, so I don't know whether it is better than nothing or better than a really beat-up original brass piece.
John Honeycutt
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 38-7 Speaker
I have let this one sit because of other duties. Now I am back, and I have a couple of questions. I hooked up a Hammond ...tludka — 05:34 PM
Philco 42-390, code 121 speaker
>>A closer examination of the very small print schematic indicates that the speaker is a PM type. This shows a ...morzh — 05:18 PM
Philco 60 Squealing
Litz is typically tinned by simply rubbing it with the soldering iron tip while immersed in solder (and a bit of rosin f...morzh — 05:14 PM
Philco 6K7
The suppressor grid (if by G3 you mean the S) is usually at the Cathode potential, which in this caes is GND. I am not ...morzh — 05:10 PM
Philco 16B Parts
Thanks for the reply. Unfortunately the radio was removed before bidding was over so I didn't get a chance to bid.dconant — 04:10 PM
Philco 16B Parts
Hi Dan, Mike is correct, there's a lot of painted stuff on the chassis but it looks pretty good. The sm is all there,sp...Radioroslyn — 03:50 PM
1930s Stromberg-Carlson Tombstone Radio need help identifying model number
Hi Cap'n Clock, Unfortunately, I do not have this radio.  This is a shame because this should be a good performer.  2A...captainclock1988 — 03:43 PM
Philco 42-390, code 121 speaker
Using a 5W  1.5k  ceramic resistor in place of the field coil and using a 4 ohm PM speaker, I was able to bring the radi...Stevelog — 02:57 PM
Philco 60 Squealing
I have taken out the 2nd IF and found a problem or not. I believe the coils are litz wire. There is a very small strand ...dconant — 02:13 PM
Philco 6K7
I am restoring a Philco 37-60. The am reception is very good, but the shortwave is very weak. Run 6 Philco removes the g...bobbyd1200 — 01:35 PM

[-]
Who's Online
There are currently 4725 online users. [Complete List]
» 2 Member(s) | 4723 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Home Radios