1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Zenith 6S229 Tombstone
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#1

12-09-2016, 08:27 PM
I have a question about The Resistance readings on the following>>>

Power Transformer
Antenna Coil
Osc Coil
Output Transformer
IF Cans

My schematic has NO values for any of these..

Or does anyone have a different schematic with values on it...

Skip...
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,288
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

12-09-2016, 09:26 PM
>Power Transformer  The highest resistance will across the HV winding(around 200-400ohms or so) next the 120v primary (10-30ohm) the the heater windings (just a few ohms)

Antenna Coil Pri pretty low 2-6ohms  secondary pretty low also about the same.
Osc Coil Same as ant coil
Output Transformer primary 200-500 ohms secondary low a few ohms

IF Cans about 10-30ohms.

Mostly when you are checking the resistance of these items you are looking for a very high resistance indicating that the winding is open.
Generally with coils the lower the frequency the higher the resistance because it take more wire to make more inductance.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#3

12-09-2016, 10:54 PM
Terry, OK great That makes perfect since..

See you on Sun..

Skip...
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#4

12-12-2016, 01:18 AM
OK,, Here are some pictures>>

[Image: http://i292.photobucket.com/albums/mm38/...je2v1r.jpg]

Dial Looks good...

[Image: http://i292.photobucket.com/albums/mm38/...oqcelr.jpg]

Bottom of Cabinet Not so Good...

[Image: http://i292.photobucket.com/albums/mm38/...iagumv.jpg]


Oh goody.. More Mouse Drops??

[Image: http://i292.photobucket.com/albums/mm38/...gsbnjn.jpg]

Top Pretty rusty.. Its a copper Chassis..

[Image: http://i292.photobucket.com/albums/mm38/...gslqgo.jpg]

Under Chassis after Mouse removals..

Not to bad.. Next on to checking out Transformer and coils..

Anyone know what to use for this belt?? Its for the tuning..

[Image: http://i292.photobucket.com/albums/mm38/...xmenrr.jpg]

Skip...
Find
Dan Walker
Senior Member
****
Posts: 371
Threads: 103
Joined: Jul 2011
City: Calgary, AB, CA
#5

12-12-2016, 11:56 AM
http://www.adamsradio.com/page1.html

 Here is where you can get the belt you need.
   It looks like you have your work cut out on this one, but it should turn out good .
 Dan in Calgary
 
   Living in Calgary Alberta
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#6

12-13-2016, 01:04 AM
Ok, Update: The Transformer, Antenna Coil, Osc Coil and IF cans all have Continuity.. Nothing Open..

So now waiting on a Price ..

Can someone please tell me approx what to offer for this..I do not want to Low ball but also do not want to over pay...

This is from the ( Pickers house) That I had set aside. I liked the looks and cabinet wasn't Bad..

Help Please

Thanks
Skip...
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#7

12-13-2016, 09:05 PM
Couple of more questions:...

There are 3 extra Variable Trimmer caps in bottom of radio that I cannot ID Circled in RED..
Any Clue What they are for?

[Image: http://i292.photobucket.com/albums/mm38/...45xtjp.jpg]

Here is alignment Instructions

[Image: http://i292.photobucket.com/albums/mm38/...ynksrw.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...ztqf4g.jpg]


Also is this Factory??

[Image: http://i292.photobucket.com/albums/mm38/...whd30b.jpg]

Skip...
Find
Eliot Ness
Phorum Expert
*****
Posts: 3,135
Threads: 54
Joined: Apr 2011
City: Lexington, KY
#8

12-17-2016, 06:32 PM
(12-13-2016, 01:04 AM)vecher Wrote:  ......So now waiting on a Price ..

Can someone please tell me approx what to offer for this..I do not want to Low ball but also do not want to over pay...

Need to see a picture of the cabinet and how many of the Zenith wood knobs does it have? 

The 6-S-229 has a photo finish so condition plays into the value:

http://www.radiophile.com/6s229.htm
John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#9

12-17-2016, 06:59 PM
Ok, I will take picture.. It has 3 of the 4 Knobs Missing 1 knob..

Skip...
Find
morzh
Odobenus rosmarus
*****
Posts: 15,835
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#10

12-17-2016, 07:57 PM
Skip

To be perfectly honest I never care about exact resistance reading of coils. If the coil is original and not open, it is OK and this is a fact. And you can tell open (infinite ohms)or leakage (hundreds of K to Megs to Gigs) from real resistance (units to tens of Ohms in RF coils, hundreds ohms in output xfmr primaries etc). And ohmmeter will not tell you about turn shorts.

So it is a waste of time to try to find out exact numbers. See if it is open. If not, it is presumed good. Rare cases of leakages and turn shorts are diagnosed by symptoms.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#11

12-17-2016, 08:46 PM
Ok,Thanks all.. Here are pictures of Cabinet..

[Image: http://i292.photobucket.com/albums/mm38/...iwicec.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...abrrk4.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...gxejhk.jpg]

[Image: http://i292.photobucket.com/albums/mm38/...nx5pft.jpg]

Skip...
Find
OldRestorer
Electronic geneus
*****
Posts: 4,109
Threads: 310
Joined: Nov 2013
City: Kings Park NY
#12

12-17-2016, 09:34 PM
Hey,
The Photofinish looks good to me.. I would just clean up the cabinet personally.
If you want it better then strip the top only and refinish it...
DO NOT touch the photofinish...
Black magic marker will fix the trim issues...
I know you dont do cabinets (yet) but this is an easy one....

I think $75.00 max.. Probably $50.00...

Me
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Find
morzh
Odobenus rosmarus
*****
Posts: 15,835
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#13

12-17-2016, 10:12 PM
Easy for you to say. If I were shocked 60 times, I'd say the same. Icon_lol
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
vecher
Phorum Expert
*****
Posts: 933
Threads: 140
Joined: Mar 2015
City: Lansdale State, Province, Country: PA
#14

12-19-2016, 12:08 AM
Have another question... How do you clean the dial? It seems to have spots .. I think when cleaning the pots some cleaner might have gotten on it.. I do not remember seeing them there before..

[Image: http://i292.photobucket.com/albums/mm38/...0nphbv.jpg]

Waiting on parts and belts .. Should be here this week .. Then start recap..

Thanks...

Skip
Find
morzh
Odobenus rosmarus
*****
Posts: 15,835
Threads: 554
Joined: Oct 2011
City: Jackson, NJ
#15

12-19-2016, 09:09 AM
Find an inconspicuous spot, try mineral spirits.
If it works, you could do the rest.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 4 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Various and Sundry Categories
  3. Other Radios (Non-Philco)