Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Overview: How to Add Images to Your Posts
#1

The management is frequently asked how one may post an image with their text posts here.

There are two ways to do this: using your own website space or one of the photo hosting websites, or using the "Upload attachment" tab which is visible underneath the box where you type in your text to make a post here.

1. Pictures hosted at an external source

When using images in your posts with this method, they must point to an image on a website. This could be your own personal website, or the storage space some ISPs (Internet Service Providers) give to you for storing image files such as this.

For your picture to show up in your post, it must be written out like this:

[Image: https://philcoradio.com/images/phorum/Ph...xample.jpg]

without the spaces before and after the URL (address where your image is at).

Of course, you will substitute the site where your image is at for "yourwebsite.com," and the name of your image for "image.jpg".

Need a place to host your pictures?

See here:
https://philcoradio.com/phorum/showthread.php?tid=4371

2. Attaching image files to your posts

This information has been revised and moved to:
https://philcoradio.com/phorum/showthread.php?tid=4407

Hope this helps, and thanks very much for your participation in the Philco Phorum!
#2

Another question which frequently comes up is, My images are too large and I cannot post them!

This is no longer relevant as Nathan has made adjustments which allows very large photos to be displayed in the Phorum.




Users browsing this thread: 2 Guest(s)
[-]
Recent Posts
462ron
Hi Dan, your original dial appears to be lighter, easier to allow light through. My original is similar except it’s crac...462ron — 12:07 PM
Philco 38-2 Automatic Tuning
I received my new 38-2 dial. I'm a little disappointed. As you can see in the picture the blues have a white shadow. The...dconant — 11:13 AM
Philco 38-2 Low Volume
I have been playing my 38-2 for a while now and it is doing very well. I did have to replace the 6A8 (osc) as it develop...dconant — 11:03 AM
Philco Speaker Spider
Hello, Does anyone with a 3 D printer make the spiders for those old Philco speakers? That might be a good idea for some...dconant — 09:41 AM
Philco 16B Parts
Hello, I'm looking to buy a 16B but I'm not so sure of what I am looking at. First as seen from the picture it looks lik...dconant — 09:17 AM
Looking for verification of correct schematic.
Klondike98, Thank you. I'll double check that SN and get back to you. GarySP, Thank you for the schematic.RossH — 12:13 AM
Looking for verification of correct schematic.
I think you have the correct take on your set. Ron's annotated early schematics that note the below B22000 serial numbe...klondike98 — 12:04 AM
Looking for verification of correct schematic.
Hello Ross. The Philco Radio Library located at the bottom of the page has the schematic with the tube count you have. ...GarySP — 10:48 PM
HiFi (Chifi) tube amp build - but my own design.
Tim It's be interesting if you put your schematic here. Who knows, you could get some advice from a few folks here. ...morzh — 10:01 PM
Philco 42-390, code 121 speaker
Thanks for that information. It would appear from the output transformer parts list that the transformer that was origi...Stevelog — 07:21 PM

[-]
Who's Online
There are currently 1240 online users. [Complete List]
» 1 Member(s) | 1239 Guest(s)
Avatar

>