1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
38-12 Dial Face Removal
Winky Dink
Member
***
Posts: 122
Threads: 22
Joined: Dec 2013
City: Meridian, ID
#1

04-13-2017, 01:13 PM
Is there any way to remove the pointer so that I can remove the cardboard dial face before I start cleaning the chassis?

[Image: https://c1.staticflickr.com/4/3933/34016...2bc7_z.jpg]

Thanks,
Henry.
Find
KCMike
Phorum Expert
*****
Posts: 1,475
Threads: 69
Joined: Nov 2012
City: Kansas city, MO.
#2

04-13-2017, 01:49 PM
I restored one quite awhile back. I think that dial pointer just pulls off. Not easily, be careful with it.
Find
morzh
Odobenus rosmarus
*****
Posts: 15,691
Threads: 551
Joined: Oct 2011
City: Jackson, NJ
#3

04-13-2017, 03:16 PM
It pulls out, pretty simply. Pull the pointer by the hub, not by the hand, use your fingernails to pull it. be gentle, not much effort is needed.
When using your nails, make sure you feel the pressure your joints exert onto the dial face to be very light - it is easily smushed.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
(This post was last modified: 04-13-2017, 03:17 PM by morzh.)
Find
Winky Dink
Member
***
Posts: 122
Threads: 22
Joined: Dec 2013
City: Meridian, ID
#4

04-13-2017, 03:47 PM
Thanks. I hadn't found the edge of the hub, but I have exactly the right tool and I'll get to it tonight.
Find
Winky Dink
Member
***
Posts: 122
Threads: 22
Joined: Dec 2013
City: Meridian, ID
#5

04-14-2017, 01:13 AM
This is why I couldn't find the hub.  I held the rotor still and gave a little twist to the pointer.  Then it slid off easily.

[Image: https://c1.staticflickr.com/3/2886/33984...0850_n.jpg]
Thanks again.
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM

[-]
Who's Online
There are currently 5312 online users. [Complete List]
» 2 Member(s) | 5310 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Cabinet Restoration