Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

General Electric Old and New
#1

I mentioned I got a GE AA5 from a pal at work, cabinet is cleaned up, epoxiied inside and about done. The numberson the dial are fragile and I am not going to clean in that spot anymore not to rub them off. No model number and I have not found it in an archive yet.

On another GE note featured are 2 probably early eighties models recently found on the bay. Rare for me to go there and rarer to buy. I needed a better portable and this looked clean and the little table set fits on my small kitchen table. Both are surprisingly sensitive and sound pretty good. The portable is a good AM Dxer at nite.
Total for both less than 25.00. So by most standards not very vintage but by 2017 standards very vintage. Table set #7-4115B portable #7-2857A

Chassis GE pics added now.

https://www.flickr.com/photos/92577012@N...1360369981

Here is the Delmonico I mentioned...
https://www.flickr.com/photos/92577012@N...0376229113

Paul

Tubetalk1
#2

Hey, ANY analog radio today IS vintage.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#3

Don't know why, but I have always liked those Delmonico radios.  I think it must be the odd ball name and dual speakers, how does it sound Paul?

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#4

have not played it yet, a bit leary. Need to see the underside of the chassis. The fellow who owned it had put tape on the dial where his fave statios were, tried some goo gone and a razor but need to be very careful getting the gunk off.

Will let you know. 

I always liked Delmonico potatoes!

paul

Tubetalk1




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM
40-150 General questions
I think RobB has it right. It is a part number and looks like its stamped on the chassis and that wasn't something you ...klondike98 — 11:41 AM
40-150 General questions
It's most likely a part number. Most of Philco part numbers are in that format. I looked at the parts list for this mode...RodB — 08:10 AM
40-150 General questions
Hi Kevin, No, I don't but I like your Quote about being a good electrician. The way I look at it is "The fact ...MrFixr55 — 08:06 AM
Philco 38-7 Speaker
7K should be fine. While not a perfect match (This transformer is meant for 6V6 tubes), Antique Electronic Supply (AES)...MrFixr55 — 08:03 AM
40-150 General questions
I discovered a stamp on the underside of the breadboard on my Philco 40-150. It is"56-1417' in black ink with numbe...Kevin_D — 07:14 AM
Philco 38-7 Speaker
FYI the Impedance of the HR20 (the one I have) secondary of the audio transformer is 5 ohms. The 38-7XX speaker is suppo...tludka — 04:22 PM

[-]
Who's Online
There are currently 2813 online users. [Complete List]
» 3 Member(s) | 2810 Guest(s)
AvatarAvatarAvatar

>