Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Please ID this Silvertone
#1

Please ID Cannot find any info or schematic on this..

[Image: https://farm5.staticflickr.com/4050/3490...f0b0_b.jpg]


Thanks
Skip...
#2

Sears Silvertone 1764 in riders 4-3
It is the only one with a 1v tube in the lineup.
See link

http://www.grillecloth.com/sylvania/tube...ubmit&db=3

Riders 4-3
http://www.americanradiohistory.com/Arch...34-STU.pdf

Icon_smile


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#3

Thanks Kirk... Was in Joe's shed.. Got it for 10.00

Also got a Heathkit IT-11 Cap tester for 15.00

My heathkit C-3 is not working..

Skip...
#4

Hope your resistance line cord is good! If not you'll need to scare up a 7.4mf non polarized cap to drop the heater voltage.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Nice little depression set Skip!


(05-23-2017, 06:39 AM)Radioroslyn Wrote:  Hope your resistance line cord is good! ......

What are the odds of that?  We used to find them N.I.B. and you could hear them crack as you tried to straighten them out  Icon_e_surprised

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#6

I think I have still have a few of them around some where. Got to preheat them to avoid the crackels.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#7

boy that shed is never ending Icon_crazy




sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#8

Geeze,
I better get back there before you clean it out Skip, Icon_lol

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#9

Just what you need some more curtain burners!!!!!![Image: http://philcoradio.com/phorum/images/smi...on_eek.gif]

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#10

Yup Every time I go in there I find something Different I had not seen before..

Skip...
#11

Where do I find a 7.4uf Cap?

Skip...
#12

8uf will work,,,,can,,, I ,,have a hall pass to the Shed,,,,I can help clean it out ,,,lololol,,,
#13

I will check with Joe He is the one doing this for a friend..

I will let everyone know if he has another open house per say.. He is a good friend and its only about 10 minutes from me..

Skip..
#14

Hey Skip,
Insteadi of finding a 7.4 non polarize cap you could use a 140 ohm resistor @20w or better, and 1N4007.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#15

Terry, I heard that Diodes seem to fail a lot..Maybe that's not true.. Could you draw where in the circuit they should go?

Skip...




Users browsing this thread:
[-]
Recent Posts
Philco 91 Speaker Replacement
The spider is glued on the cone and so is the voice coil. I think you can use a cotton swab dipped in acetone and carefu...RodB — 02:42 PM
Restoring Philco 37-604C
Yes I saw that. If I knew, I'd probably try to arrange for getting it myself. But I have just got one. Which does not m...morzh — 01:44 PM
Philco 38-2 Automatic Tuning
When you push the lever, you are supposed to rotate the disk to the desired station. Then the magnetic tuning will acqu...morzh — 01:42 PM
Philco 38-2 Automatic Tuning
I figure out the muting from another picture that helped. Now I need to know how the automatic tuning works. When I push...dconant — 12:11 PM
Philco 91 Speaker Replacement
How would I go about removing the spider from the cone?dconant — 12:04 PM
Philco 38-2 Automatic Tuning
Hello, I am having trouble getting my automatic tuning to stay unmuted. If I play with the tuning handle I can get it to...dconant — 10:51 AM
Does anyone make photofinish replacements?
Here’s the link to the DIY photofinish section of our site: klondike98 — 09:46 AM
Delco car radio Peko vibrator converstion issues
Hi Richard, Thx for posting the schematic.  As I remember as a kid, these were great performers for the time, likely...MrFixr55 — 08:56 AM
Delco car radio Peko vibrator converstion issues
hello mr Fixr, The Electro  Powersupply that I am powering the radio with has a huge choke plus a 10,000ufd electrolyti...radiorich — 10:58 PM
Delco car radio Peko vibrator converstion issues
How about putting a choke in the power supply? The big cap was likely an attempt to stabilize the DC. Kids who cre...MrFixr55 — 09:19 PM

[-]
Who's Online
There are currently no members online.

>