Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Please ID this Silvertone
#1

Please ID Cannot find any info or schematic on this..

[Image: https://farm5.staticflickr.com/4050/3490...f0b0_b.jpg]


Thanks
Skip...
#2

Sears Silvertone 1764 in riders 4-3
It is the only one with a 1v tube in the lineup.
See link

http://www.grillecloth.com/sylvania/tube...ubmit&db=3

Riders 4-3
http://www.americanradiohistory.com/Arch...34-STU.pdf

Icon_smile


Attached Files Image(s)
   

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#3

Thanks Kirk... Was in Joe's shed.. Got it for 10.00

Also got a Heathkit IT-11 Cap tester for 15.00

My heathkit C-3 is not working..

Skip...
#4

Hope your resistance line cord is good! If not you'll need to scare up a 7.4mf non polarized cap to drop the heater voltage.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#5

Nice little depression set Skip!


(05-23-2017, 06:39 AM)Radioroslyn Wrote:  Hope your resistance line cord is good! ......

What are the odds of that?  We used to find them N.I.B. and you could hear them crack as you tried to straighten them out  Icon_e_surprised

John KK4ZLF
Lexington, KY
"illegitimis non carborundum"
#6

I think I have still have a few of them around some where. Got to preheat them to avoid the crackels.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#7

boy that shed is never ending Icon_crazy




sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#8

Geeze,
I better get back there before you clean it out Skip, Icon_lol

Icon_smile

Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
#9

Just what you need some more curtain burners!!!!!![Image: http://philcoradio.com/phorum/images/smi...on_eek.gif]

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#10

Yup Every time I go in there I find something Different I had not seen before..

Skip...
#11

Where do I find a 7.4uf Cap?

Skip...
#12

8uf will work,,,,can,,, I ,,have a hall pass to the Shed,,,,I can help clean it out ,,,lololol,,,
#13

I will check with Joe He is the one doing this for a friend..

I will let everyone know if he has another open house per say.. He is a good friend and its only about 10 minutes from me..

Skip..
#14

Hey Skip,
Insteadi of finding a 7.4 non polarize cap you could use a 140 ohm resistor @20w or better, and 1N4007.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#15

Terry, I heard that Diodes seem to fail a lot..Maybe that's not true.. Could you draw where in the circuit they should go?

Skip...




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Cannot Adjust an IF Transformer’s cores
The abilities of our 'Phorum Pholks" never ceases to amaze me! Fantastic fabrication, Joseph! I'm waiting now for...GarySP — 08:27 PM
PT-6 antenna connections
Thanks. I never realized that was a notch noted in the schematic as described. I’ll recheck my wiring.bridkarl — 08:13 PM
Cannot Adjust an IF Transformer’s cores
Thank you! I was quite new to the Phorum when I started this post, so I feel like it might be advantageous to publish a ...jrblasde — 08:07 PM
PT-6 antenna connections
Notice in the schematic the notch at the bottom of the antenna coil is between pins 3 & 4. Yes, pin 6 of the 7C6 is...RodB — 07:34 PM
bridkarl
I have two PT-6 chassis. On both there is a blue wire that runs from the above chassis transformer to pin 6 of 7C6. So t...bridkarl — 07:23 PM
Cannot Adjust an IF Transformer’s cores
Joseph, now you are an engineer!!RodB — 06:37 PM
PT-6 antenna connections
Hi, reading your explanation I can see the confusion. If you take it one connection at a time it should result in a desi...RodB — 06:34 PM
Cannot Adjust an IF Transformer’s cores
It works! I received the PCBs this morning in the mail, and put everything together. I reused the base from the original...jrblasde — 04:32 PM
PT-6 antenna connections
I seem to have lost my way on this PT-6. I see the antenna aerial transformer schematic - I’m reading pins 1 through ...bridkarl — 12:30 PM
40-150 General questions
Good thing you're a good electrician ... the pictures show a lot of rewiring in your future! Take care and BE HEALTHY!...GarySP — 11:52 AM

[-]
Who's Online
There are currently 4119 online users. [Complete List]
» 2 Member(s) | 4117 Guest(s)
AvatarAvatar

>