Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Bakelite capacitor block
#1

Restoring a Philco 650 and have 6 of the bakelite capacitor blocks to rebuild. I used to go to the Philco site where there was a section of diagrams showing internal wiring for the different blocks. With the remake of the site the list and the diagrams are gone. Anyone know where the information exists?

The other parts values are missing as well. Help.

Thanks.
#2

Find it here  
http://philcoradio.com/phorum/showthread.php?tid=14964

The book was just listed very good book too   Icon_thumbup
http://philcoradio.com/phorum/showthread.php?tid=16946

Sam

Some day, and that day may never come, I will call upon you to do a service for me. But until that day, accept this justice as a gift
mafiamen2
#3

Sam,

Thanks so much. I'm in your debt God Father.

John
#4

If you're referring to the Philco Repair Bench, try the Wayback Machine. The entire old site is archived.

https://web.archive.org/web/201603242327...lokcap.htm

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
#5

Thanks Jeff. Great find.
#6

(07-18-2017, 07:47 AM)jmac3ky Wrote:  Thanks Jeff. Great find.

I'm afraid I can't take credit. Someone else here on the Phorum pointed it out recently.

Once I saw it, I immediately went through all the archived pages and saved PDFs as a reference. Icon_thumbup

Blessings,
Jeff W.
Jonesboro, Arkansas

http://jeffsradios.weebly.com

God loves you as you are, not as you should be, because none of us are as we should be. - Brennan Manning
#7

Chuck is in the process of updating his Philco Repair Bench website so the info should all reappear there in time.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

[-]
Who's Online
There are currently 6335 online users. [Complete List]
» 1 Member(s) | 6334 Guest(s)
Avatar

>