1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Chassis 39-3A1 wiring
slink
New Member
*
Posts: 1
Threads: 1
Joined: Jun 2017
City: Hope, BC CAN
#1

08-01-2017, 08:15 PM
Hoping for some help with a few loose wires on this radio.  Apparently it is the Canadian version of a popular chassis. It worked fine 30 years ago but storage and transit has taken its toll.  There are two wires that have come un-soldered.  I have included photos to help identify the component and loose wire.

https://www.flickr.com/photos/157292344@...res/6256R5

Wire #1 comes off the tall skinny thing next to the tuner, it is greenish/grey in color
Wire #2 comes off a resistor attached to the chassis down at the same end as the tall skinny thing in image 1.

From my descriptions it should be apparent that i'm a Newb.  Any simple explanations or tips would be greatly appreciated.

https://www.flickr.com/gp/157292344@N02/781C64
Find
Radioroslyn
Phorum Expert
*****
Posts: 7,285
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
#2

08-01-2017, 11:47 PM
Hi Steve and welcome,

> There are two wires that have come un-soldered.
Geez and I thought it was hot in PA!!

My best guess is that those wire are the antenna and ground for the set. These weren't solder to anything to start with.
Does the set play when it plugged in, turned on, and an antenna is connected??
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
Find
klondike98
Phorum Moderator
******
Posts: 5,088
Threads: 270
Joined: Nov 2012
City: Wilsonville State, Province, Country: OR
#3

08-03-2017, 09:21 AM
Welcome to the Phorum!
Icon_wave
Cheers,
Bob
[Image: https://www.dropbox.com/s/5m63ib99yfx2eg....jpg?raw=1]
Bob's Restorations Web Page
Website Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

[-]
Who's Online
There are currently 5477 online users. [Complete List]
» 2 Member(s) | 5475 Guest(s)
AvatarAvatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration