Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

41-280 alignment
#1

I've finished re-capping a 41-280 chassis and replacing out of tolerance resistors. Now I'm working on the alignment. The IF alignment went OK as did the broadcast and police bands. Both of these bands track perfectly across the dial.

The problem is the overseas band. I can peak compensator 17A at 12 mHz but compensator 2 has no effect. The image signal is 910 mHz above the fundamental as per the instructions, but at the same volume (not weaker). Also, the tracking is way off at the lower end of the dial. For example WRMI 9395 comes in at 9500 and the image can be heard at 10410 at the same volume.

I'm beginning to think the overseas oscillator coil may be bad. 

Any thoughts would be appreciated.

Dave
#2

Welcome to the Phorum!
Icon_wave
#3

Hi Dave and welcome,
As a troubleshooting measure I'd loose couple a frequency counter to the oscillator.  Frequency received or dial frequency = oscillator frequency - 455kc.
It's important that the osc is running above the incoming signal rather than below.
Have you check the XXL/7A4 osc tube, it may be weak causing the osc to die out at hf.
GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

How do you "loose couple" a frequency counter to the oscillator? Through a .1 uf capacitor to the oscillator plate? I'd like to try this just for fun, and to have a new technique to use for the future.

John Honeycutt
#5

Hi John,
I just wrap a few turns of hook up wire around the osc tube. Depending on the circuit you could use a capacitor to couple it but .1 is way too large, this could stop the oscillator from oscillating or dramatically shift it's frequency. The idea of loose coupling is to just couple a small amount of signal with out interfering with oscillator frequency. For capacitance coupling the counter I'd use something on the order of 5-20mmfd. Being kinda lazy I'll grab some wire and make a gimmick cap.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Delco car radio Peko vibrator converstion issues
Rich, There is an Australian website (Cool386.com) that has much useful info regarding repair and restoration of vibr...Joe Rossi — 07:29 PM
Jackson 715 not working
Mrfixr55, its working now. I cleaned the switches and sockets with spray cleaner. Thanks for helping on this one.daveone23 — 06:26 PM
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM

[-]
Who's Online
There are currently 3290 online users. [Complete List]
» 2 Member(s) | 3288 Guest(s)
AvatarAvatar

>