1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
Speaker rebuilding
BILL
Member
***
Posts: 160
Threads: 36
Joined: Jan 2006
#1

01-23-2006, 07:33 PM
OK this may have been gone over before but I'm new to the Philco Phorum I have a 1930 Transitone auto radio my speaker is beat- needs to be reconed and the coils are open, this speaker is very similar ,design wise, to the old Atwater Kent cone speakers of the 1920's ,magnet and pin, high impedance , the cone is the heavier material than newer speakers and is quite shallow anyone got Ideas?
Find
Chuck Schwark
Phorum Expert
*****
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
#2

01-23-2006, 08:18 PM
Try one of these speaker re-conning services maybe? Hank is highly recommended most often in all the Fora I frequent.

John's Vintage Radio
John Sworen, Owner
144 N. Beverwyck Rd., #208
Lake Hiawatha, NJ 07034
(973) 575-0717
E-mail: Js1radio@aol.com
Website: http://www.johnsvintageradio.com/recone.html

Hank Brazeal
3850 Galleria Woods Dr., #8
Burmingham, AL 35244
Ph: 205-403-6243
E-mail: hankspkr@charter.net

Neal's Speaker Service
Ron Neal
9300 Matador Way
Sacramento, CA 95826
Ph: 916-363-6524
E-mail: nealspeakers2@msn.com
Website: http://www.nealspeakerrepair.com

Orange County Speaker, Inc.
Bryan Sunda
12141 Mariners Way
Garden Grove, CA 92843
Ph: 800-897-8373
Website: http://www.speakerRepair.com
Chuck Schwark,
The Philco Repair Bench
[Image: http://www.philcorepairbench.com/images/philog3tiny.gif]
http://www.philcorepairbench.com
Website Find
BILL
Member
***
Posts: 160
Threads: 36
Joined: Jan 2006
#3

01-30-2006, 05:40 PM
Thanks Chuck Icon_biggrin Icon_biggrin
Find
« Next Oldest | Next Newest »




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 60 Squealing
All correct shields must be in place, all tubes correct no subs of any kind. Check any soldered, riveted ground conne...Chas — 01:24 PM
Philco 60 Squealing
I have recapped and replaced out of tolerance resistors and so on. Radio plays nicely on fairly strong stations. The pro...dconant — 10:55 AM
Philco 46-420 Code 121 Reception issues
Welcome Eric, I agree with Bob and far as the two main electrolytic filter capacitors did you change them yourself or w...radiorich — 11:43 PM
Philco 46-420 Code 121 Reception issues
You mentioned the Philco manual and going through the check points...just to be sure we're on the same page here's the m...klondike98 — 08:13 PM
Philco 42-1008 conversion kit
Interesting. I haven't seen that before.klondike98 — 07:02 PM
12' Philco
Yes I had looked for it on the web as well some time back and could not find it. I was glad to see it turned up in Ron'...klondike98 — 06:59 PM
Shadow Meter Bulb
Now if you had a set with a tuning light then the bulb type is important to the circuit, some sets used those prior to t...Arran — 04:58 PM
Shadow Meter Bulb
Ok. Thanks for the correction.RossH — 03:09 PM
Model 28L
For 28 you will probably need to buy a Hammond 125CSE. Or any of the series of the power you need, with SE suffix. Then ...morzh — 02:09 PM
37-60 revision 6
I am restoring a Philco 37-60 and it shows run 6 they removed the ground from G3 of the 6K7G and put the G3 to -2.5v for...bobbyd1200 — 01:01 PM

[-]
Who's Online
There are currently 6312 online users. [Complete List]
» 1 Member(s) | 6311 Guest(s)
Avatar

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration