Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Kolster K-20 A.F. Transformer
#1

Hello, all.

Tried posting this on another site but didn't get any responses. Since I've always had good luck here, I thought I'd ask another newbie question: is anyone able to tell me what size A.F. transformers are used in a Kolster K-20? They are marked AFT1 and AFT2 on the schematic which can be found here:

http://www.nostalgiaair.org/pagesbymodel...040092.pdf

Thank you in advance for any help.

Dave
#2

Perhaps a couple universal output transformers like the P-T291 from AES?
#3

Hi Dave,
>able to tell me what size A.F. transformers are used in a Kolster K-20?
I'm not sure I understand what you are asking. Are you referring to physical size?? Or electrical equivalent??

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#4

Electrical equivalent
#5

Ok What you are looking for are https://www.tubesandmore.com/products/tr...tage-10-ma  for both. If the transformers are enclosed and have a 1/2" core you can buy just the replacement winding.

GL

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry
#6

Other then the generic AES transformer you could try an Edcor one, or try the solid state substitute circuit that was featured in the A.W.A Old Timer's Bulletin about ten years ago, I think it's posted online somewhere.
Regards
Arran
#7

Thank you for the help.

Dave




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
New Philco Repair Bench
I am sure this is the archive, and not the Chuck's site.morzh — 09:50 PM
Made mistake & did not label connection
It's not like we are good friends with that wire and can tell it from other ptetty identical looking wires. Why'n't you...morzh — 09:49 PM
Made mistake & did not label connection
I'm not sure why that wire wasn't covered in the video. I'm pretty sure the 6A8 won't work until that pin is grounded. Y...RodB — 09:47 PM
Made mistake & did not label connection
You'll have to forgive me, I am not sure what you mean.  Can you explain what you are really saying.  If anyone does not...georgetownjohn — 08:05 PM
Made mistake & did not label connection
Those are details better left to the ones who know. Maybe you disconnected the wrong end of the wire.RodB — 06:22 PM
Made mistake & did not label connection
Maybe this is starting to make some sense in my hard head.  Is this why the wire in question was not in the great Ron Ra...georgetownjohn — 04:34 PM
Made mistake & did not label connection
I was correct with the 6A8 pin connection's, 7 and 8 are connected to ground as well as the tube shield (the broken line...RodB — 02:41 PM
Made mistake & did not label connection
What does the dotted line representing that surrounds the tube in the schematic?georgetownjohn — 02:17 PM
Made mistake & did not label connection
Hello John, I have been there either label got lost or was not labeled ! Sincerely Richardradiorich — 02:15 PM
Made mistake & did not label connection
Sorry, it is a Philco 37-640.  Does that help?--Johngeorgetownjohn — 02:14 PM

[-]
Who's Online
There are currently no members online.

>