Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

40-216 restoration questions
#31

So from what I have found through previous posts here #95 is actually an electrolytic but Philco changed it to NP at some point.

I already put in a 16uf 250v electrolytic, it should be ok then at least for a while?

As far as #88 goes I'm checking what I have to make a NP cap.

So far the best match I have found are two 80uF/40v. I think the V is to low though according to some calculations I've seen in threads. Would the resulting V for the two caps together be lower, like around 24v?

I also have two 47uF/100v but then I'm dropping the capacitance to 23.5uF

Trying to work with what I have. :\
#32

Slow on the feedback these days Icon_sad

How about these?

https://www.ebay.com/itm/112380229987?rmvSB=true
#33

How about this one.

Which side should the Neutral/Hot of the power cord go?

The HOT side gets a fuse if I add, correct?
#34

Yes typically the hot side gets the fuse.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#35

Edisla;

I noticed the same issue when I restored my 40-201. Your 40-216 is similar with the thumb-wheel controls. Philco did not design in detents on these models because it apparently caused too much resistance to rotation of the knobs. I had even taken some detent ball bearings from another radio to install in the Philco only to discover there was no way to cause the ball bearing to be retained and had to drop the idea. The bandswitch action is sort of sloppy, but does work OK. This issue is seen on all the models with the thumb-wheel bandswitch knobs.

Joe
#36

Edisla;

The 30uF capacitor you are wondering about is a non-polarized electrolytic so that it can be used in and AC circuit. The motor in question is an AC powered motor which gets its voltage from a transformer and there are no rectifiers changing the power from that transformer to DC, so that is why they used a non-polarized capacitor. Do not try to use a single electrolytic with just a positive and negative lead attached across the AC to the motor. It will overheat and likely explode! To make a non-polarized electrolytic from two conventional DC type electrolytics you either connect two of them together by tying the two negative leads together OR tie two positive leads together and make connections to the motor using the two wires from the free end leads of the two capacitors. It is safer and usually takes up less space to just buy an AC rated motor run capacitor of the right capacitance. A film type capacitor made for AC service at 115-130VAC will work fine at 30VAC that the motor appears to operate at.

Joe
#37

Two electrolytics simply connected back to back do not make a NP cap. The center pin has to be biased as otherwise you still run AC voltage through two polarized caps. In case of this motor, which is (did not look at the sch but sure it is the case) decoupled via any DC bias through the transformer, you do not have any suitable voltage to hook up to, so the two caps solution won't work.
But unless I am mistaken, the cap is across the secondary winding of the motor which may give out low voltage. Why don't you measure it first.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#38

I have not done any power up yet.

That is the last cap I am needing to replace before I go with power up.

Should I do power bring up with the old cap disconnected and not work the motor and if all goes well check the voltage you are asking about?
#39

Yes. I'd do the radio first, and then when all is playing, start on the turntable.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#40

No turntable on this one ;)
#41

Well, whatever the motor does Icon_smile
It rotates sonething Icon_lol

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#42

Turns the Volume up/down and unit Off.

Radio is powered up. I left the original cap but only get buzzing from motor at this point. It's not turning. Does turn by hand.

Have new cap on order.
#43

Did the back to back caps since I figured with the buzzing that the cap was bad and it works. Motor turns now.

Once the correct cap comes in the mail I'll swap it out. For now I have powered down and will continue with replacing wiring.
#44

Is 22 gauge stranded wire to small to use for the power transformer leads?

Original looks a bit bigger but I only have 22 on hand :\
#45

I would go a little heavier on the primary and heater leads 18-20ga.

When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!

Terry




Users browsing this thread: 6 Guest(s)
[-]
Recent Posts
Jackson 715 not working
Now that you posted the schematic, I don't know why that Sprague electrolytic cap is across the meter, as it is not indi...MrFixr55 — 05:51 PM
HiFi (Chifi) tube amp build - but my own design.
What may be lacking in the PP Tube amps may be the 2nd harmonics, which some, especially RCA back in the day called &quo...MrFixr55 — 05:32 PM
Jackson 715 not working
Usually in an emission tester, the tube under test is measured as if it were a diode. So, some testers connect all the g...RodB — 04:17 PM
Restoring Philco 37-604C
Yep. F5 is green, D5 is Red. Red is Bad. Green is Clean.morzh — 01:30 PM
Jackson 715 not working
I did start to do that but I stalled out because I could not figure out how the grid and plate get voltage. In this diag...daveone23 — 11:52 AM
Restoring Philco 37-604C
(Insert Homer Simpson "DOPF" Here.) When all fails, look at the can. Took the Ron Ramirez advice, red Caig D...MrFixr55 — 09:23 AM
Philco 91 Speaker Replacement
From your text I am not sure if you intend to use the existing speaker with a resistor instead of the field coil. It wo...morzh — 08:44 AM
Philco 91 Speaker Replacement
My field coil is bad. I am still hoping to find an original, but if I can't I will go with a fitting Philco speaker, 125...dconant — 08:34 AM
Philco 91 Speaker Replacement
As Rod said, it is OK to use a fitting speaker, and then look for an original one. If you buy a Hammond 125 output tr...morzh — 08:15 AM
Philco 91 Speaker Replacement
Yes, I often have to substitute, then keep an eye out for an original. In the meantime, the radio is working and being e...RodB — 08:02 AM

[-]
Who's Online
There are currently no members online.

>