Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

New member / Model 60 Restoration On-going
#1

Hi All,

My first post here, and while I have a question, I'll ask it under an already existing thread that it's related to.

Overall, I just wanted to commend you, Ron and all, on the useful information that I've seen so far relating not only to Philcos, but which is also useful for restorations in general.

Ron, your document that pulls together the evolution of the model 60 was especially useful to me since I'm restoring a late model version (the H schematic within your document) for my father, and time is of the essence on this one!

I've done a few radio restorations so I'm not really a newby, but your experience on Philco-specific issues has been VERY helpful to me (aka coil rewinding). I'm an EE, and love working on guitar amps and pedals, and I've done a 41-285 restoration, Trans-oceanic, 46-350 repairs, etc. I have a 630 tombstone that I want to get to next.

The model 60 is coming along, and I have to -- guess what -- do rewinds on the antenna and oscillator coil primaries, as you've talked about elsewhere.

So, thanks again, and if I ever have any wisdom to add here, I'll certainly try!

Scottie
#2

Scottie, welcome. I am sorry I have not participated much here of late. I am in college, and I have a particularly tough semester right now, so I am staying very busy.

--
Ron Ramirez
Ferdinand IN
#3

Ron,

No problem -- I've been busy, too! The model 60 is 98% done, just a few more cosmetic items. The coil winding went just fine, using 34awg wire.

I've thought about furthering the degree, but then I re-think it. Having the time would be a problem!

Good luck with it!

Scottie




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 41-608 changer coupler
3D-printing...short of machining, of course. Or molding.morzh — 05:20 PM
Philco 41-608 changer coupler
Thanks, Morzh. That solves the issue of the rubber pieces. Now, I need to find a way to replicate the pot metal piec...alangard — 05:07 PM
12' Philco
If it is 12', either Kareem or Andre would have to jump pretty high to look at the front panel. Kareem would have an e...morzh — 01:48 PM
12' Philco
And here's a story about the tires on the truck. Same "no-stoop" guy must have installed these! Take care a...GarySP — 01:17 PM
Hickok AC51 tube tester
I think they have only shown the secondaries of the transformer. Two of them feed the rectifiers' filaments.morzh — 12:58 PM
IF can wire size and Rubber mounts?
Arran If the wire inside cans is the gauges you mentioned, the sole reason for that would be mechanical, to stiffen t...morzh — 12:56 PM
12' Philco
Rod, Yes, I know, but the Giant Philco is not around anymore either, so I go by whoever was alive fairly recently. H...morzh — 12:54 PM
Hickok AC51 tube tester
Absolutely no one is going to reverse engineer that circuit. Even the iron core is missing.RodB — 10:37 AM
IF can wire size and Rubber mounts?
Thanks to both members for your help regarding wire and tuner mtg supports. regards--Johngeorgetownjohn — 09:33 AM
Hickok AC51 tube tester
Note that no power cord, power switch, or power transformer switch are shown. That (along with my experience with full s...DaleHCook — 07:09 AM

[-]
Who's Online
There are currently no members online.

>